Journal of Micro and Nano: Recent submissions
Now showing items 181-200 of 372
-
Electrohydrodynamic Printing for Advanced Micro/Nanomanufacturing: Current Progresses, Opportunities, and Challenges
(The American Society of Mechanical Engineers (ASME), 2018)The paper provides an overview of high-resolution electrohydrodynamic (EHD) printing processes for general applications in high-precision micro/nanoscale fabrication and manufacturing. Compared with other printing approaches, ... -
Editorial
(The American Society of Mechanical Engineers (ASME), 2018) -
Electrohydrodynamic Casting Bismuth Telluride Microparticle-Loaded Carbon Nanofiber Composite Material With Multiple Sensing Functions
(The American Society of Mechanical Engineers (ASME), 2018) -
Nanoparticle Sintering Model: Simulation and Calibration Against Experimental Data
(The American Society of Mechanical Engineers (ASME), 2018)One of the limitations of commercially available metal additive manufacturing (AM) processes is the minimum feature size most processes can achieve. A proposed solution to bridge this gap is microscale selective laser ... -
Fabrication and Wettability Analysis of Hydrophobic Stainless Steel Surfaces With Microscale Structures From Nanosecond Laser Machining
(The American Society of Mechanical Engineers (ASME), 2018)In this work, nanosecond laser machining is used to fabricate hydrophobic 17-4 PH stainless steel surfaces with microscale and submicron structures. Four surface structures were designed, with microscale channels and pillars ... -
Graphene Growth on and Transfer From Platinum Thin Films
(The American Society of Mechanical Engineers (ASME), 2018)This paper presents graphene growth on Pt thin films deposited with four different adhesion layers: Ti, Cr, Ta, and Ni. During the graphene growth at 1000 °C using conventional chemical vapor deposition (CVD) method, these ... -
Model-Based Coarse-Fine Virtual Calibration and Visual Servo for Augmented Reality-Assisted Peg-in-Hole Microassembly
(The American Society of Mechanical Engineers (ASME), 2018)A three-dimensional (3D)-virtual calibration and visual servo are implemented for augmented reality (AR)-assisted peg-in-hole microassembly operations. By employing 3D model and ray casting, the 3D coordinates on virtual ... -
Investigations for Enhancing Wear Properties of Rapid Tooling by Reinforcement of Nanoscale Fillers for Grinding Applications
(The American Society of Mechanical Engineers (ASME), 2018)In this work, investigations were made for enhancing wear properties of rapid tooling (RT) by reinforcement of fillers (nanoscaled) for grinding applications. The RT has been prepared by using biocompatible composite ... -
Fabrication of Micro Diamond-Like Carbon-Nozzles by Plasma Oxidation Printing
(The American Society of Mechanical Engineers (ASME), 2018)The plasma oxidation printing (POP) was proposed as a digital manufacturing to shape the diamond-like carbon (DLC) thick film into a micronozzle on the tool steel substrate. Its head shape was first designed by computer-aided ... -
Output-Only Modal Analysis of Micromilling Systems
(The American Society of Mechanical Engineers (ASME), 2018)An output-only modal analysis (OMA) approach is presented to obtain the direct frequency response function (FRF) at the tip of the tool in micromilling setups. White noise input is provided using acoustic excitation and ... -
Low Pressure Phase Transformations During High-Speed, High-Temperature Scratching of Silicon
(The American Society of Mechanical Engineers (ASME), 2018)Higher temperature assisted processing of silicon, such as heat-assisted diamond turning, is often being considered to improve surface integrity. At higher temperatures and under mechanical loading and unloading, caused ... -
Active Mixing Nozzle for Multimaterial and Multiscale Three-Dimensional Printing
(The American Society of Mechanical Engineers (ASME), 2017)Multiscale and multimaterial three-dimensional (3D) printing is new frontier in additive manufacturing (AM). It has shown great potential to implement the simultaneous and full control for fabricated object including ... -
Special Section on Micro- and Nano-Additive Manufacturing—Part 1
(The American Society of Mechanical Engineers (ASME), 2017) -
Multiscale Stereolithography Using Shaped Beams
(The American Society of Mechanical Engineers (ASME), 2017)Current stereolithography (SL) can fabricate three-dimensional (3D) objects in a single-scale level, e.g., printing macroscale or microscale objects. However, it is difficult for the SL printers to fabricate a 3D macroscale ... -
Influence of High Duty Ratio and Frequency in WECM Employing In Situ Fabricated Wire Electrode
(The American Society of Mechanical Engineers (ASME), 2017)To adapt with today's rapidly changing world, fabrication of intricate microparts is becoming an urgent need. Manufacturing of these microparts with stringent requirements necessitates the early adoption of different ... -
Simulation of Micro/Nanopowder Mixing Characteristics for Dry Spray Additive Manufacturing of Li-Ion Battery Electrodes
(The American Society of Mechanical Engineers (ASME), 2017)A new dry spraying additive manufacturing method for Li-ion batteries has been developed to replace the conventional slurry-casting technique for manufacturing Li-ion battery electrodes. A dry spray manufacturing process ... -
Effect of Substrate and Nanoparticle Spacing on Plasmonic Enhancement in Three-Dimensional Nanoparticle Structures
(The American Society of Mechanical Engineers (ASME), 2017)Surface plasmon polaritons associated with light-nanoparticle interactions can result in dramatic enhancement of electromagnetic fields near and in the gaps between the particles, which can have a large effect on the ... -
Study of Microscale Three-Dimensional Printing Using Near-Field Melt Electrospinning
(The American Society of Mechanical Engineers (ASME), 2017)Three-dimensional (3D) printing of microscale structures with high-resolution (submicron) and low-cost is still a challenging work for the existing 3D printing techniques. Here, we report a direct writing process via ... -
A Computer-Aided Design and Manufacturing Implementation of the Atomic Force Microscope Tip-Based Nanomachining Process for Two-Dimensional Patterning
(The American Society of Mechanical Engineers (ASME), 2017)This paper reports a feasibility study that demonstrates the implementation of a computer-aided design and manufacturing (CAD/CAM) approach for producing two-dimensional (2D) patterns on the nanoscale using the atomic force ... -
Fabrication of Double-Layered Alginate Capsules Using Coaxial Nozzle
(The American Society of Mechanical Engineers (ASME), 2017)Multilayered encapsulation has been of great interest for various pharmaceutical, chemical, and food industries. Fabrication of well-defined capsules with more than one shell layer still poses a significant fabrication ...