Journal of Fluids Engineering: Recent submissions
Now showing items 8921-8940 of 9024
-
Application of a General Boundary Layer Analysis to Turbulent Boundary Layers Subjected to Strong Favorable Pressure Gradients
(The American Society of Mechanical Engineers (ASME), 1975)Theoretical predictions of turbulent boundary layer development under the influence of strong favorable pressure gradients made using a finite-difference calculation procedure are compared to ... -
Hydraulic Transport of Single Spheres in a Horizontal Pipe
(The American Society of Mechanical Engineers (ASME), 1975) -
Inlet Filter Effects on Three-Dimensional Channel Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1975) -
Influence of Entrained Water Mass on the Vibration Modes of a Shell
(The American Society of Mechanical Engineers (ASME), 1975)The virtual mass effect of a liquid annulus surrounding a shell is established in closed form. Simple support conditions for the shell and open end conditions for the liquid annulus are ... -
Comprehensive Design of Axisymmetric Wind Tunnel Contractions
(The American Society of Mechanical Engineers (ASME), 1975)Design charts for wind tunnel contractions are developed using an inviscid, incompressible flow analysis. A contour formed of two cubic arcs joined smoothly together was found to be a good ... -
Operation of an Open Canopy Fume Hood in a Crossflow
(The American Society of Mechanical Engineers (ASME), 1975) -
Effective Moments of Inertia of Oscillating Fluid-Filled Rings and Spheres
(The American Society of Mechanical Engineers (ASME), 1975) -
A Turbulent Energy Model for Flows With Drag Reduction
(The American Society of Mechanical Engineers (ASME), 1975)A simple turbulent energy model, based on an improved version of Wolfshtein’s model for Newtonian flows, with a variable damping parameter, is used to describe the effect of linear polymers ... -
Slip Flow in the Entrance Region at Low Reynolds Numbers
(The American Society of Mechanical Engineers (ASME), 1975) -
Three-Dimensional Turbulent Boundary Layer in a Rotating Helical Channel
(The American Society of Mechanical Engineers (ASME), 1975)An analytical and experimental investigation of the characteristics of a three-dimensional turbulent boundary layer in a rotating helical channel is reported in this paper. Expressions are developed ... -
Foreign Report: Industrial Turbomachinery R&D in India
(The American Society of Mechanical Engineers (ASME), 1975) -
Review—Complex Turbulent Flows
(The American Society of Mechanical Engineers (ASME), 1975)“Complex” turbulent flows are those which cannot be predicted with acceptable accuracy by methods developed in classical thin shear layers. This is a subjective and time-dependent definition but ... -
Performance of Three Vaned Radial Diffusers With Swirling Transonic Flow
(The American Society of Mechanical Engineers (ASME), 1975)A unique vortex nozzle facility has been conceived and developed to simulate the exit flow from a high pressure ratio centrifugal compressor impeller. Visual studies and performance measurements ... -
Effect of Specific Heat Ratio, Impeller Tip Running Clearance, and Compressor Insulation on High-Pressure-Ratio Centrifugal Compressor Modeling
(The American Society of Mechanical Engineers (ASME), 1975)Results are displayed which show the effect of gas specific heat ratio, impeller tip running clearance, and compressor insulation on modeling of a high-pressure-ratio compressor’s performance. The ... -
Effect of Turbulence in Free Stream on Cavitation Incipience of Hydrofoil
(The American Society of Mechanical Engineers (ASME), 1975)It was proved experimentally that the conditions of cavitation incipience, such as the positions of incipient cavitation bubble formation and collapse, extent of cavitation, and the propensity ... -
An Analysis of the Hydraulic Ram
(The American Society of Mechanical Engineers (ASME), 1975)An hydraulic ram is a pump in which the momentum of a driving stream of water undergoing a small head drop is used to pump a small portion of the stream to a head considerably greater ... -
Discussion: “Metering Performance Investigation and Substantiation of the Universal Venturi Tube—Part I—Hydraulic Shape and Discharge Coefficient” (Halmi, D., 1974, ASME J. Fluids Eng., 96, pp. 124–131)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “An Experimental Investigation of Transition of Plane Poiseuille Flow” (Karnitz, M. S., Potter, M. C., and Smith, M. C., 1974, ASME J. Fluids Eng., 96, pp. 384–388)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Experimental Investigation of the Vortex Street Generated by a Plane Jet in a Counter Flow” (Robillard, L., and Ramamurthy, A. S., 1974, ASME J. Fluids Eng., 96, pp. 43–48)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “An Approximate Method for the Solution of a Class of Nonlinear Equations in Fluid Mechanics and Magnetohydrodynamics” (Nath, G., 1973, ASME J. Fluids Eng., 95, pp. 439–444)
(The American Society of Mechanical Engineers (ASME), 1975)