Journal of Fluids Engineering: Recent submissions
Now showing items 8881-8900 of 9024
-
Opinion
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Theoretical Investigations and Numerical Evaluations of Wall Effects in Cavity Flows” (Popp, S., 1975, ASME J. Fluids Eng., 97, pp. 482–491)
(The American Society of Mechanical Engineers (ASME), 1975) -
The Disappearance of the Wake Shock Behind a Cylinder in a Supersonic Flow at High Reynolds Number
(The American Society of Mechanical Engineers (ASME), 1975) -
On Recirculating Flow in a Dead-End Vessel
(The American Society of Mechanical Engineers (ASME), 1975) -
A Comment On Some Falkner-Skan Solutions
(The American Society of Mechanical Engineers (ASME), 1975) -
A Reattachment Analysis for Closure of the Supersonic Base Flow Problem
(The American Society of Mechanical Engineers (ASME), 1975) -
Swirling Flow of a Dissociated Gas
(The American Society of Mechanical Engineers (ASME), 1975) -
The Momentum-Integral Equation for a Boundary Layer With Turbulence or Ordered Unsteadiness in the Free Stream
(The American Society of Mechanical Engineers (ASME), 1975)The two-dimensional momentum integral equation is derived for the case where free-stream turbulence or ordered unsteadiness exist. It is shown that extra terms may arise, of which one, the shear ... -
Discussion: “Calculated Design Data for the Multiple Disk Turbine Using Incompressible Fluid” (Lawn, Jr., M. J., and Rice, W., 1974, ASME J. Fluids Eng., 96, pp. 252–258)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Gas Compression With the Liquid Jet Pump” (Cunningham, R. G., 1974, ASME J. Fluids Eng., 96, pp. 203–215)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Jet Break-Up and Mixing Throat Lengths for the Liquid Jet Gas Pump” (Cunningham, R. G., and Dopkin, R. J., 1974, ASME J. Fluids Eng., 96, pp. 216–226)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion
(The American Society of Mechanical Engineers (ASME), 1975) -
Fluid Transients
(The American Society of Mechanical Engineers (ASME), 1975) -
A Note on the Transition Observations on an Axisymmetric Body and Some Related Fluctuating Wall Pressure Measurements
(The American Society of Mechanical Engineers (ASME), 1975)Boundary layer transition on an axisymmetric body up to Reynolds number of 1.26 × 106 was observed by schlieren method of flow visualization developed for water tunnel use. The spectrum ... -
An Efficient Method for Simulating Frequency-Dependent Friction in Transient Liquid Flow
(The American Society of Mechanical Engineers (ASME), 1975)An efficient procedure is developed for simulating frequency-dependent friction in transient laminar liquid flow by the method of characteristics. The procedure consists of determining an approximate ... -
Flow Regimes in Two-Dimensional Ribbed Diffusers
(The American Society of Mechanical Engineers (ASME), 1975)Water table flow visualization tests of a straight wall diffuser and corresponding ribbed diffuser were conducted over a wide range of total divergence angles and diffuser length to throat width ... -
Solid Particle Demixing in a Suspension Flow of Viscous Gas
(The American Society of Mechanical Engineers (ASME), 1975)The motion of a medium consisting of an incompressible viscous fluid and suspended solid particles was analyzed from the standpoint of continuum mechanics. It was assumed that the particles’ ... -
Velocity Measurements in Wet Steam Flows by Laser Anemometry and Pitot Tube
(The American Society of Mechanical Engineers (ASME), 1975)Velocities up to 200 m/s in condensing steam flows have been successfully measured using a laser Doppler anemometer, without artificial seeding. The performance of the system is described and ... -
Simultaneous Measurements of Reynolds Stress and Turbulent Kinetic Energy for Two-Dimensional Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1975) -
Forces on Screens Inclined to a Fluid Flow
(The American Society of Mechanical Engineers (ASME), 1975)