Journal of Fluids Engineering: Recent submissions
Now showing items 8841-8860 of 9024
-
Flow Distribution Manifolds
(The American Society of Mechanical Engineers (ASME), 1976)Flow distribution in the lateral branches of dividing, combining, reverse, and parallel flow manifold systems is studied both analytically and experimentally. Predictions for the flow rates and ... -
Prediction of the Trajectory of a Turbulent Jet Injected Into a Crossflowing Stream
(The American Society of Mechanical Engineers (ASME), 1976)A semianalytical prediction of the trajectory of a turbulent jet issuing at various angles to the horizontal into a crossflowing stream is presented. The predictive technique utilizes the basic ... -
Channel Flow Over a Smooth-to-Rough Surface Discontinuity With Zero Pressure Gradient
(The American Society of Mechanical Engineers (ASME), 1976)Measurements are given for the combined effects of a change of surface roughness and a simultaneous change of pressure gradient. The latter is negative in a fully developed turbulent, two-dimensional ... -
Turbulent Boundary Layer and Flow Resistance on Plates Roughened by Wires
(The American Society of Mechanical Engineers (ASME), 1976)The flow resistance in a plate roughened by equally spaced wires at right angles to the flow direction was investigated experimentally by measuring the turbulent boundary layer developing along ... -
Vibration of Deriaz Pumps at Dos Amigos Pumping Plant
(The American Society of Mechanical Engineers (ASME), 1976)Severe vibration problems were encountered during initial operation of large Deriaz pumps. This paper describes those problems, the alternative solutions available, and the corrective action taken. ... -
Orifice Cavitation and Its Effect on Spray Mixing
(The American Society of Mechanical Engineers (ASME), 1976)Cavitation characteristics were determined for sharp-edged orifices. Both circular and rectangular orifices were studied. A simple model is proposed, which was experimentally verified over a range ... -
Performance of Hydraulic Gas Compressors
(The American Society of Mechanical Engineers (ASME), 1976)A hydraulic gas compressor has no moving parts and compresses gas at the expense of hydraulic energy by means of entrainment in a downward moving column of liquid with subsequent separation ... -
Tales of Misteaks
(The American Society of Mechanical Engineers (ASME), 1976) -
REVIEW—Progress in Numerical Turbomachinery Analysis
(The American Society of Mechanical Engineers (ASME), 1976)Progress achieved in numerical analysis during the past decade now permits the turbo-machinery designer to carry out a wide variety of inviscid, steady flow, two-dimensional calculations for ... -
Discussion: “Laser-Doppler Measurements in a Subsonic Jet Injected into a Subsonic Cross Flow” (Rudinger, George, and Moon, L. F., 1976, ASME J. Fluids Eng., 98, pp. 516–520)
(The American Society of Mechanical Engineers (ASME), 1976) -
The First Stenning Memorial Lecture: Alan Hugh Stenning—1928–1973—Distinguished Engineer
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Theoretical and Experimental Study of Wall Region Periodicity for Turbulent Pulsatile Flow” (Thomas, L. C., and Shukla, R. K., 1976, ASME J. Fluids Eng., 98, pp. 27–32)
(The American Society of Mechanical Engineers (ASME), 1976) -
Methods for Reducing Losses Across Fluid Metering Nozzles
(The American Society of Mechanical Engineers (ASME), 1976)This paper concerns the pressure losses involved in measuring flow rate. These losses can be large and affect the choice of pump or flow metering section to be used. Solutions are developed ... -
Discussion: “Turbulent Wall Jets With Cylindrical Streamwise Surface Curvature” (Wilson, D. J., and Goldstein, R. J., 1976, ASME J. Fluids Eng., 98, pp. 550–557)
(The American Society of Mechanical Engineers (ASME), 1976) -
Development of a Retracting Vane/Centrifugal Main Fuel Pump for Gas Turbine Engines
(The American Society of Mechanical Engineers (ASME), 1976)Fuel pumps and metering systems are becoming more complex and expensive to meet the high performance requirements of advanced gas turbine engines. A simple, inlet throttled, centrifugal pump ... -
Discussion: “Prediction of the Trajectory of a Turbulent Jet Injected Into a Crossflowing Stream” (Sucec, J., and Bowley, W. W., 1976, ASME J. Fluids Eng., 98, pp. 667–672)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Analysis of Turbulent Unseparated Flow in Subsonic Diffusers” (Harsha, P. T., and Glassman, H. N., 1976, ASME J. Fluids Eng., 98, pp. 320–322)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Vibration of Deriaz Pumps at Dos Amigos Pumping Plant” (Ruud, F. O., 1976, ASME J. Fluids Eng., 98, pp. 674–679)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Channel Flow Over a Smooth-to-Rough Surface Discontinuity With Zero Pressure Gradient” (Islam, O., and Logan, E., 1976, ASME J. Fluids Eng., 98, pp. 626–632)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Influence of the Axisymmetric Contraction Ratio on Freestream Turbulence” (Ramjee, V., and Hussain, A. K. M. F., 1976, ASME J. Fluids Eng., 98, pp. 506–515)
(The American Society of Mechanical Engineers (ASME), 1976)