Journal of Fluids Engineering: Recent submissions
Now showing items 8681-8700 of 9024
-
Discussion: “Effect of Specific Heat Ratio, Impeller Tip Running Clearance, and Compressor Insulation on High-Pressure-Ratio Centrifugal Compressor Modeling” (Block, J. A., and Runstadler, Jr., P. W., 1975, ASME J. Fluids Eng., 97, pp. 174–179)
(The American Society of Mechanical Engineers (ASME), 1976) -
Transverse Curvature Effect on the Flow Field in a Laminar Cylindrical Wall Jet
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Forces on Unstaggered Airfoil Cascades in Unsteady In-Phase Motion With Applications to Harmonic Oscillation” (Kemp, N. H., and Ohashi, H., 1976, ASME J. Fluids Eng., 98, pp. 521–530)
(The American Society of Mechanical Engineers (ASME), 1976) -
Combined Free and Forced Laminar Convection in a Bingham Plastic on a Vertical Flat Plate
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Control of Free-Stream Turbulence by Means of Honeycombs: A Balance Between Suppression and Generation” (Loehrke, R. I., and Nagib, H. M., 1976, ASME J. Fluids Eng., 98, pp. 342–351)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Some Characteristics of Cavity Flow Past Cylindrical Inducers in a Venturi” (Syamala Rao, B. C., and Chandrasekhara, D. V., 1976, ASME J. Fluids Eng., 98, pp. 461–466)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “The Suppression of Flow Separation by Sequential Wall Jets” (North, P., 1976, ASME J. Fluids Eng., 98, pp. 447–452)
(The American Society of Mechanical Engineers (ASME), 1976) -
Measurement of the Propagation of Long-Wavelength Disturbances Through Turbulent Flow in Tubes
(The American Society of Mechanical Engineers (ASME), 1976)Phase velocities and attenuation factors for the propagation of small amplitude long wavelength sinusoidal disturbances, measured in a tube with turbulent liquid flow, are reported. Three frequency ... -
Decaying Annular Swirl Flow With Inlet Solid Body Rotation
(The American Society of Mechanical Engineers (ASME), 1976)An experimental investigation of a low-speed turbulent swirling flow in a stationary, concentric, annular duct was made. The experiment involved isothermal air as the working fluid in an annulus ... -
Effect of Wetting on Friction Factors for Turbulent Flow of Mercury in Annuli
(The American Society of Mechanical Engineers (ASME), 1976)Friction factors were determined for fully developed turbulent flow of mercury in smooth concentric annuli under conditions where either both walls were unwetted, or both were wetted, or the ... -
A Separated and Reattached Flow on a Blunt Flat Plate
(The American Society of Mechanical Engineers (ASME), 1976)Velocity, pressure, and turbulence measurements were made in the separated, reattached, and redeveloped regions of a two-dimensional incompressible flow over a flat plate with finite thickness and ... -
Fully Developed Laminar Flow in Curved Rectangular Channels
(The American Society of Mechanical Engineers (ASME), 1976)The Navier-Stokes equations are solved by a numerical method for steady, fully developed, incompressible, laminar flow in curved rectangular channels considering the curvature ratio effect in the ... -
Microbubble Spectra and Superheat in Water and Sodium, Including Effect of Fast Neutron Irradiation
(The American Society of Mechanical Engineers (ASME), 1976)The microbubble spectrum in a sample of tap water was measured by the Coulter counter technique under various conditions, and at the same time the tensile strength (i.e., “superheat” capacity) ... -
Liquid Jet Pumped by Rising Gas Bubbles
(The American Society of Mechanical Engineers (ASME), 1976)From observations of a stream of gas bubbles rising through a liquid, a two-phase mathematical model is proposed for calculating the induced turbulent vertical liquid flow. The bubbles provide ... -
Oil Slick Instability and the Entrainment Failure of Oil Containment Booms
(The American Society of Mechanical Engineers (ASME), 1976)The onset of droplet formation from contained oil slicks is interpreted to be due to the breaking of finite amplitude interfacial waves. These waves result from the equilibration of amplifying ... -
Effects of the Axisymmetric Contraction Shape on Incompressible Turbulent Flow
(The American Society of Mechanical Engineers (ASME), 1976)The performance characteristics of four different axisymmetric contraction shapes with the same contraction ratio are experimentally investigated for incompressible flow. The pre- and postcontraction ... -
Effect of Polymer Additives on Jet Cavitation
(The American Society of Mechanical Engineers (ASME), 1976)Cavitation in a fluid jet discharged under the surface of a similar fluid was studied using water and dilute solutions of poly(ethylene oxide), a drag-reducing polymer. The addition of a few ... -
Letter to the Editor: What Limits the Speed of Marine Transportation?
(The American Society of Mechanical Engineers (ASME), 1976) -
Optimal Selection of Pumps in an Hydraulic Network
(The American Society of Mechanical Engineers (ASME), 1976)The selection of pumps in an hydraulic network (such as those found in plant firewater systems or hydraulic control systems) is formulated as a mixed integer nonlinear program. The design ... -
Discussion: “Solid Particle Demixing in a Suspension Flow of Viscous Gas” (Hamed, A., and Tabakoff, W., 1975, ASME J. Fluids Eng., 97, pp. 106–111)
(The American Society of Mechanical Engineers (ASME), 1976)