Journal of Fluids Engineering: Recent submissions
Now showing items 8441-8460 of 9024
-
Mechanical Models for Tubular Reactor Fuel Elements
(The American Society of Mechanical Engineers (ASME), 1962) -
Summary of the Session
(The American Society of Mechanical Engineers (ASME), 1962) -
Cumulative Damage in Creep-Rupture Tests of a Carbon Steel
(The American Society of Mechanical Engineers (ASME), 1962)A life-fraction rule is often used to predict the rupture life of a piece of elevated-temperature equipment exposed to several temperature and stress conditions. It is based on the assumption ... -
Notched-Bar Creep Rupture of a Cast Heat-Resistant Alloy at Temperatures Where Ductility Is Limited
(The American Society of Mechanical Engineers (ASME), 1962)Rupture life of a cast nickel-base alloy was increased by the presence of a mild notch even for test temperatures and nominal stresses at which unnotched specimens had fracture elongations of ... -
An Empirical Creep Law From a Single Test
(The American Society of Mechanical Engineers (ASME), 1962)A method is described by which an empirical creep law, relating stress, strain, and strain rate, may be obtained from a single constant-load creep test. An example to illustrate the method ... -
Influence of Ductility on Creep Rupture Under Multiaxial Stresses
(The American Society of Mechanical Engineers (ASME), 1962)Creep-rupture times at 1200 and 1400 deg F were compared for notched versus unnotched bars and for thin-walled tubes in uniaxial tension versus combined tension and internal pressure to give ... -
Notch Rupture Behavior as Influenced by Specimen Size and Preparation
(The American Society of Mechanical Engineers (ASME), 1962)A notch-sensitive forging was tested at 1300 F to measure the effect of machining practice and of limited variations in Kt and specimen size upon notch rupture life. Within the limits studied, ... -
Size Effect on Notched Rupture Time
(The American Society of Mechanical Engineers (ASME), 1962) -
The Effect of a “V” Notch on the Tensile Creep Behavior of Cr-Mo Steel
(The American Society of Mechanical Engineers (ASME), 1962)The effect of a “V” notch on the tensile creep behavior of Cr-Mo steel at elevated temperature was studied to elucidate the reasons for notch strengthening or notch weakening. Special attention ... -
Trends and Implications of Data on Notched-Bar Creep Rupture
(The American Society of Mechanical Engineers (ASME), 1962)Extended research on creep rupture of notched specimens, conducted at the University of Michigan under Air Force sponsorship, is analyzed along with recent publications of others. The combined ... -
Discussion: “Crack Propagation in Aluminum-Foil Laminates” (Mote, Jr., C. D., and Frisch, J., 1962, ASME J. Basic Eng., 84, pp. 257–264)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “An Empirical Creep Law From a Single Test” (Finnie, Iain, 1962, ASME J. Basic Eng., 84, pp. 236–238)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “Influence of Ductility on Creep Rupture Under Multiaxial Stresses” (Sawert, W., and Voorhees, H. R., 1962, ASME J. Basic Eng., 84, pp. 228–232)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “Notch Rupture Behavior as Influenced by Specimen Size and Preparation” (Couts, Jr., W. H., and Freeman, J. W., 1962, ASME J. Basic Eng., 84, pp. 222–225)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “Size Effect on Notched Rupture Time” (Manjoine, M. J., 1962, ASME J. Basic Eng., 84, pp. 220–221)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “The Effect of a “V” Notch on the Tensile Creep Behavior of Cr-Mo Steel” (Suezawa, Yoshitada, and Hōjō, Hidemitsu, 1962, ASME J. Basic Eng., 84, pp. 214–218)
(The American Society of Mechanical Engineers (ASME), 1962) -
Free Oscillations With Small Nonlinear Damping
(The American Society of Mechanical Engineers (ASME), 1962) -
The Use of a Venturi Tube as a Quality Meter
(The American Society of Mechanical Engineers (ASME), 1962) -
Effect of Radial Heat Transfer on the Creep Behavior of Thick-Walled Tubes Loaded by Combined Bending Moment and Internal Pressure
(The American Society of Mechanical Engineers (ASME), 1962) -
Analysis of a Bivariant Optimizing Control
(The American Society of Mechanical Engineers (ASME), 1962)