Journal of Fluids Engineering: Recent submissions
Now showing items 8061-8080 of 9024
-
Discussion: “On the Load Capacity and Stability of Rotors in Self-Acting Gas Lubricated Plain Cylindrical Journal Bearings” (Sternlicht, B., and Winn, L. W., 1963, ASME J. Basic Eng., 85, pp. 503–511)
(The American Society of Mechanical Engineers (ASME), 1963) -
Phase Distribution Mechanisms in Turbulent Two-Phase Flow in Channels of Arbitrary Cross Section
(The American Society of Mechanical Engineers (ASME), 1981)An analytical model for the phase distribution mechanisms in fully developed turbulent two-phase flow in channels of arbitrary cross sections has been derived. The model has been applied to the ... -
Low-Reynolds-Number Turbulent Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1981)This paper presents experimental wind-tunnel data that show the universal logarithmic velocity profile for zero-pressure-gradient turbulent boundary layer flows is valid for values of momentum-deficit ... -
Discussion: “An Investigation of the Mechanism of the Friction and Wear of Carbon” (Midgley, J. W., and Teer, D. G., 1963, ASME J. Basic Eng., 85, pp. 488–493)
(The American Society of Mechanical Engineers (ASME), 1963) -
The Effect of Nuclei on the Inception of Bubble and Sheet Cavitation on Axisymmetric Bodies
(The American Society of Mechanical Engineers (ASME), 1981)Hydrogen bubbles were generated as cavitation nuclei and their distributions were measured. The number and size distribution of bubble cavities generated on axisymmetric bodies was calculated and ... -
Turbomachines—A Guide to Design Selection and Theory
(The American Society of Mechanical Engineers (ASME), 1981) -
Fundamentals of Gas-Particle Flow (Vol. 2—Handbook of Powder Technology)
(The American Society of Mechanical Engineers (ASME), 1981) -
Discussion: “Measurement of Pointwise Juncture Condition of Temperature at the Interface of Two Bodies in Sliding Contact” (Ling, F. F., and Simkins, T. E., 1963, ASME J. Basic Eng., 85, pp. 481–485)
(The American Society of Mechanical Engineers (ASME), 1963) -
Discussion: “The Initiation Of Gaseous Microbubble Growth In Laminar Separation Bubbles” (Parkin, B. R., 1981, ASME J. Fluids Eng., 103, pp. 543–549)
(The American Society of Mechanical Engineers (ASME), 1981) -
Discussion: “Cavitation Inception in Spool Valves” (Martin, C. Samuel, Medlarz, H., Wiggert, D. C., and Brennen, C., 1981, ASME J. Fluids Eng., 103, pp. 564–575)
(The American Society of Mechanical Engineers (ASME), 1981) -
Discussion: “Liquid Sheet Jet Experiments: Comparison With Linear Theory” (Asare, H. R., Takahashi, R. K., and Hoffman, M. A., 1981, ASME J. Fluids Eng., 103, pp. 595–603)
(The American Society of Mechanical Engineers (ASME), 1981) -
Discussion: “Aerodynamic Effects of Shape, Camber, Pitch, and Ground Proximity on Idealized Ground-Vehicle Bodies” (George, A. R., 1981, ASME J. Fluids Eng., 103, pp. 631–637)
(The American Society of Mechanical Engineers (ASME), 1981) -
Drag Reducing Polymer in Helicoidal Flow
(The American Society of Mechanical Engineers (ASME), 1981)A novel flow configuration was explored for the study of the behavior of drag reducing polymers. A screw pump consisting of a smooth cylinder and a concentrically placed screw was used to ... -
Instantaneous Pressure Distribution Around a Sphere in Unsteady Flow
(The American Society of Mechanical Engineers (ASME), 1981)Pressure fluctuations on a small sphere in a periodically pulsating jet are measured in relation to the study of measurements of instantaneous static pressure in unsteady flows, where the ... -
Search for Large-Scale Coherent Structures in the Nearly Self-Preserving Region of a Turbulent Axisymmetric Jet
(The American Society of Mechanical Engineers (ASME), 1981)In an attempt to explore the existence of large-scale coherent structures in the nearly self-preserving region of an axisymmetric free air jet, a 2.54 cm air jet at a Reynolds number ReD = ... -
Correlations of Thermodynamic Effects for Developed Cavitation
(The American Society of Mechanical Engineers (ASME), 1981)The net positive suction head (NPSH) requirements for a pump are determined by the combined effects of cavitation, fluid properties, pump geometry, and pump operating point. An important part ... -
The Initiation Of Gaseous Microbubble Growth In Laminar Separation Bubbles
(The American Society of Mechanical Engineers (ASME), 1981)Flow conditions surrounding bubble-ring cavitation inception on hemispherical headforms are analyzed with respect to the initiation of air diffusion into microbubbles as is observed to occur at ... -
Prediction of Gaseous Cavitation Occurrence in Various Liquids Based on Two-Phase Flow Analogy
(The American Society of Mechanical Engineers (ASME), 1981)An analytical method for predicting the cavitation occurrence is developed applying an analogy with the choking condition of two-phase flow. The effects of the presence of inert gas and ... -
Foreign Report
(The American Society of Mechanical Engineers (ASME), 1980) -
Editorial
(The American Society of Mechanical Engineers (ASME), 1980)