Journal of Fluids Engineering: Recent submissions
Now showing items 7621-7640 of 9024
-
Application of the Adjoint Sensitivity Method to the Analysis of a Supersonic Ejector
(The American Society of Mechanical Engineers (ASME), 1984)Although the concepts of various types of ejectors have been thoroughly discussed in the literature during the past sixty years, a rigorous sensitivity analysis of the ejector’s performance has ... -
Experimental Study of the Diversion Crossflow Caused by Subchannel Blockages. Part II: Pressures in the Channels and the Comparison of the COBRA III-C Predictions With Experimental Data
(The American Society of Mechanical Engineers (ASME), 1984)In this research, the hydrodynamic behavior of two laterally interconnected channels with blockages in one of them has been studied experimentally. For blockages of different shapes and severities, ... -
The Lid-Driven Cavity Flow: A Synthesis of Qualitative and Quantitative Observations
(The American Society of Mechanical Engineers (ASME), 1984)A synthesis of observations of flow in a three-dimensional lid-driven cavity is presented through the use of flow visualization pictures and velocity and heat flux measurements. The ratio of ... -
Pulsatile Flow Through a Branching Tube With Collapsing Walls: Volumetric Flow Redistribution
(The American Society of Mechanical Engineers (ASME), 1984)A hydraulic collapse mechanism was incorporated into a recirculating pulsatile flow system to collapse an elastic branching tube in a controlled manner. Changes in volumetric flow rate into and ... -
An Analysis of Jet Stripping of Liquid Coatings
(The American Society of Mechanical Engineers (ASME), 1984)This paper presents a new analysis of the jet stripping process, as used to control coating thicknesses in the paper, photographic and galvanizing industries, and demonstrates that the inclusion ... -
Turbulent Air Flow Over Rough Surfaces: Mean Flow Parameters
(The American Society of Mechanical Engineers (ASME), 1984)The objective of the study was to examine experimentally the turbulent flow structure near a repeated-rib geometry rough-walled surface as a function of the ratio of roughness height to pipe ... -
Experimental Study of the Diversion Crossflow Caused by Subchannel Blockages. Part I: Experimental Procedures and Mass Flow Rates in the Channels
(The American Society of Mechanical Engineers (ASME), 1984)In this research, the hydrodynamic behavior of two laterally interconnected channels with blockages in one of them has been studied experimentally. For blockages of different shapes and severities, ... -
Numerical Study of Turbulent Axisymmetric Jets Impinging on a Flat Plate and Flowing Into an Axisymmetric Cavity
(The American Society of Mechanical Engineers (ASME), 1984)A numerical study is made of the characteristics of turbulent submerged axisymmetric incompressible jets impinging on a flat plate and flowing into an axisymmetric cavity. The purpose of the ... -
Some Effects of Upstream Turbulence on the Unsteady Lift Forces Imposed on Prismatic Two Dimensional Bodies
(The American Society of Mechanical Engineers (ASME), 1984)Measurements of fluctuating lift are reported from four fixed rectangular prisms and a fixed circular cylinder, for various intensities of turbulence in the oncoming stream. Variations of unsteady ... -
Discussion: “Experiments on the Buckling of Thin Fluid Layers Undergoing End-Compression” (Blake, K. R., and Bejan, A., 1984, ASME J. Fluids Eng., 106, pp. 74–78)
(The American Society of Mechanical Engineers (ASME), 1984) -
Erratum: “Flow Field Due to Free Convection in Dead-End Channels” (Journal of Fluids Engineering, 1984, 106, pp. 217–222)
(The American Society of Mechanical Engineers (ASME), 1984) -
Rarefied Gas Flow Through a Circular Orifice and Short Tubes
(The American Society of Mechanical Engineers (ASME), 1984)Rarefied gas flow through a circular orifice and short tubes has been investigated experimentally, and the conductance of the aperture has been calculated for Knudsen number between 2 × ... -
An Analysis of the Motion of Pigs Through Gas Pipelines
(The American Society of Mechanical Engineers (ASME), 1984)A one-dimensional, quasi-steady, model describing the motion of a pig moving in a gas pipeline is developed for the cases of a solid pig, which obstructs the cross section of the pipe, and ... -
Discussion: “The Utilization of Specially Tailored Air Bubbles as Static Pressure Sensors in a Jet” (Ooi, K. K., and Acosta, A. J., 1984 ASME J. Fluids Eng., 106, pp. 459–464)
(The American Society of Mechanical Engineers (ASME), 1984) -
Discussion: “An Acoustic Detection Method of Cloud Cavitation” (Arai, C., ASME J. Fluids Eng., 106, pp. 466–475)
(The American Society of Mechanical Engineers (ASME), 1984) -
Discussion: “Confined Flow in a Partially-Filled Rotating Horizontal Cylinder” (Haji-Sheikh, A., Lakshimanarayanan, R., Lou, David Y. S., and Ryan, Phil J., 1984, ASME J. Fluids Eng., 106, pp. 270–278)
(The American Society of Mechanical Engineers (ASME), 1984) -
Nonlinear Taylor Instability in a Cylindrical Vessel
(The American Society of Mechanical Engineers (ASME), 1984)A new class of Taylor-unstable waves, consisting of ring waves appearing at the interface of two fluids of differing densities within a around pipe when the interface is accelerated in the ... -
Air Release During Column Separation
(The American Society of Mechanical Engineers (ASME), 1983)Air release caused by column separation in a pipeline was investigated in a test facility where column separation could be generated for any desired length of time. The temperature, pressure, ... -
Effects Of Surface Solidification on the Stability Of Multi-Layered Liquid Films
(The American Society of Mechanical Engineers (ASME), 1983)The linear stability problem of a n-layered liquid film with a solidified liquid-air interface is reviewed. The general formulation is applied to the special case of a two-layered film flow ... -
A Multigrid Scheme for Three-Dimensional Body-Fitted Coordinates in Turbomachine Applications
(The American Society of Mechanical Engineers (ASME), 1983)An efficient numerical scheme for the generation of curvilinear body-fitted coordinate systems in three dimensions is presented. The grid is obtained by the solution of a system of three elliptic ...