Journal of Fluids Engineering: Recent submissions
Now showing items 7141-7160 of 9024
-
Measurement of Intake Valve/Cylinder Boundary Flows Using a Multiple Orientation Hot-Wire Technique
(The American Society of Mechanical Engineers (ASME), 1988)A new measurement method is utilized to determine velocity distributions on the intake-valve/cylinder boundary for different induction system designs. The velocity information is being used to ... -
Discussion: “On Cathodic Protection in Cavitation Damage” (Plesset, M. S., 1960, ASME J. Basic Eng., 82, pp. 808–818)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “The Selection of Length and Head Scales for Cavitation Tests” (Danel, Pierre, and Duport, Jacques, 1960, ASME J. Basic Eng., 82, pp. 784–789)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “A Review of Surge-Tank Stability Criteria” (Jaeger, Charles, 1960, ASME J. Basic Eng., 82, pp. 765–775)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Viscous Dispersion in Water Hammer” (Walker, Jr., M. L., Kirkpatrick, E. T., and Rouleau, W. T., 1960, ASME J. Basic Eng., 82, pp. 759–763)
(The American Society of Mechanical Engineers (ASME), 1960) -
Fluid Motion Within the Cylinder of Internal Combustion Engines—The 1986 Freeman Scholar Lecture
(The American Society of Mechanical Engineers (ASME), 1987)The flow field within the cylinder of internal combustion engines is the most important factor controlling the combustion process. Thus it has a major impact on engine operation. This paper ... -
Improvement of Unstable Characteristics of an Axial Flow Fan by Air-Separator Equipment
(The American Society of Mechanical Engineers (ASME), 1987)The authors’ previous papers demonstrated that an air-separator is the most effective equipment among various different types for the improvement of unstable characteristics of an axial-flow rotor. ... -
Calculation of Three-Dimensional Boundary Layers on Rotating Turbine Blades
(The American Society of Mechanical Engineers (ASME), 1987)An assessment has been made of the applicability of a three-dimensional boundary-layer analysis to the calculation of heat transfer and streamline flow patterns on the surfaces of both stationary ... -
Performance Characteristics of a Multiple-Disk Centrifugal Pump
(The American Society of Mechanical Engineers (ASME), 1987) -
Dynamics of Liquid Sloshing in Upright and Inverted Bladdered Tanks
(The American Society of Mechanical Engineers (ASME), 1987)The sloshing of liquids in tanks that use a flexible, inextensible bladder to contain the liquid is investigated experimentally and theoretically. The bladder affects both the configuration of ... -
Drop Size Distribution and Air Velocity Measurements in Air Assist Swirl Atomizer Sprays
(The American Society of Mechanical Engineers (ASME), 1987)Detailed measurements of mean drop size (SMD) and size distribution parameters have been made using a Fraunhofer diffraction particle sizing instrument in a series of sprays generated by an air ... -
Suppression of Sheet Cavitation Inception by Water Discharge Through Slit
(The American Society of Mechanical Engineers (ASME), 1987)This paper studies experimentally the suppression effect of water discharge on incipient and developed sheet cavitation on a hemispherical headform. The water is discharged tangentially from a ... -
Further Studies on Laminar Flow About a Rotating Sphere in an Axial Stream
(The American Society of Mechanical Engineers (ASME), 1987) -
Discussion: “Velocity Fluctuations at the Walls of a Packed Bed of Spheres for Medium Re-Numbers” (Bahnen, R. H., and Stojanoff, C. G., 1987, ASME J. Fluids Eng., 109, p. 242)
(The American Society of Mechanical Engineers (ASME), 1987) -
Instability of Flow Through Tube Rows
(The American Society of Mechanical Engineers (ASME), 1987) -
Discussion: “Scrutinizing the k-ε Turbulence Model Under Adverse Pressure Gradient Conditions” (Rodi, W., and Scheuerer, G., 1986, ASME J. Fluids Eng., 108, pp. 174–179)
(The American Society of Mechanical Engineers (ASME), 1987) -
Discussion: “Critical Condition of Cavitation Occurrence in Various Liquids” (Kamiyama, S., and Yamasaki, T., 1986, ASME J. Fluids Eng., 108, pp. 428–432)
(The American Society of Mechanical Engineers (ASME), 1987) -
Analysis of Liquid and Structural Transients in Piping by the Method of Characteristics
(The American Society of Mechanical Engineers (ASME), 1987)Since liquid-filled piping systems are composed of slender elements, their transient behavior can be described as one-dimensional wave phenomena. Seven wave components are identified: coupled axial ... -
Incompressible Laminar Flow Past a Transversely Vibrating Cylinder
(The American Society of Mechanical Engineers (ASME), 1987)An implicit finite difference scheme in primitive variables is used for analysis of unsteady, laminar flow past transversely vibrating cylinders. Predictions of flow past an impulsively started ... -
Motion of Particles in Gases: Average Velocity and Pressure Loss
(The American Society of Mechanical Engineers (ASME), 1987)A simplified physical model is developed for the motion of solid particles in gaseous streams confined by walls (channel or pipe flow). The equations of motion for the particle are solved and ...