Journal of Fluids Engineering: Recent submissions
Now showing items 6541-6560 of 9024
-
Three-Dimensional Finite-Volume Method for Incompressible Flows With Complex Boundaries
(The American Society of Mechanical Engineers (ASME), 1992)A finite-volume method is presented for calculating incompressible 3-D flows with curved irregular boundaries. The method employs structured nonorthogonal grids, cell-centered variable arrangement, ... -
Numerical Solution of the Incompressible Boundary-Layer Equations Using the Finite Element Method
(The American Society of Mechanical Engineers (ASME), 1992)A new approach to the solution of the two-dimensional, incompressible, boundary-layer equations based on the Finite Element Method in both directions is investigated. Earlier Finite Element Method ... -
Some Characteristics of the Vortical Motions in the Outer Region of Turbulent Boundary Layers (Data Bank Contribution)
(The American Society of Mechanical Engineers (ASME), 1992)Time-resolved measurements of the spanwise vorticity component, ωz , are used to investigate the motions in the outer region of turbulent boundary layers. The measurements were taken in very ... -
Vortex Shedding From a Circular Cylinder of Finite Length Placed on a Ground Plane
(The American Society of Mechanical Engineers (ASME), 1992)This paper describes a study of changes in the vortex formation and the turbulent wake from a circular cylinder with a finite aspect ratio, placed on a ground plane. The experiment was carried ... -
Redeveloping Turbulent Boundary Layer in the Backward-Facing Step Flow
(The American Society of Mechanical Engineers (ASME), 1992)An experimental study has been performed to investigate the redeveloping turbulent boundary layer beyond separation-reattachment for a transitional separated flow. By considering the distribution ... -
An Inverse Inner-Variable Theory for Separated Turbulent Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1992)An integral method is presented for computing separated and reattached turbulent boundary layers for incompressible two-dimensional flows. This method is a substantial improvement over the ... -
Turbulent Flow Near a Rough Wall
(The American Society of Mechanical Engineers (ASME), 1992)By introducing the equivalent roughness which is defined as the distance from the wall to where the velocity gets a certain value (u/uτ ≈ 8.5) and which can be represented by a simple ... -
Roughness Effects on Frictional Resistance of Enclosed Rotating Disks
(The American Society of Mechanical Engineers (ASME), 1960)The effects of surface roughness on the frictional resistance of enclosed rotating disks have been studied experimentally. Torque data were obtained over the range of disk Reynolds numbers 4 ... -
Flow Phenomena of Partially Enclosed Rotating Disks
(The American Society of Mechanical Engineers (ASME), 1960)The flow of air in the space between a rotating disk and a stationary side wall placed parallel to its surface has been investigated over a range of Reynolds numbers from 3 × 105 to ... -
Radial Distributions of Temporal-Mean Peripheral Velocity and Pressure for Fully Developed Turbulent Flow in Curved Channels
(The American Society of Mechanical Engineers (ASME), 1960)Experimental results are presented for the radial distributions of pressure and peripheral velocity for the turbulent flow of water in two closed curved channels of rectangular cross section and ... -
Precise Measurement of Clothes Insulation During Controlled Operation of the Human
(The American Society of Mechanical Engineers (ASME), 1960)It has been demonstrated that it is possible to measure the resistance of clothing as an ohmic relation between time-averaged equilibrium values of the flux of power (metabolism) and the ... -
Theoretical and Experimental Analysis of Hydrostatic Thrust Bearings
(The American Society of Mechanical Engineers (ASME), 1960)This paper presents theoretical and experimental analysis of two types of circular hydrostatic thrust bearings, using incompressible lubricants. Design equations for load-carrying capacity, stiffness, ... -
Discussion: “Analysis of Axially Loaded Annular Shells With Applications to Welded Bellows” (Hetenyi, M., and Timms, R. J., 1960, ASME J. Basic Eng., 82, pp. 741–753)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “The Quadrant Edge Orifice—A Fluid Meter for Low Reynolds Numbers” (Bogema, M., and Monkmeyer P. L., 1960, ASME J. Basic Eng., 82, pp. 729–733)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “A Study of Viscosity Effect and Its Compensation on Turbine-Type Flowmeters” (Lee, W. F. Z., and Karlby, Henning, 1960, ASME J. Basic Eng., 82, pp. 717–725)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “The Twin Throat Venturi: A New Fluid-Flow Measuring Device” (Kalinske, A. A., 1960, ASME J. Basic Eng., 82, pp. 710–713)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Burst Strengths and Deformations of Welded Composite Turbine Wheels as Related to Weld Quality and Plasticity Calculations” (Holms, A. G., and Repko, A. J., 1960, ASME J. Basic Eng., 82, pp. 695–708)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Low-Cycle Fatigue of Two Nickel-Base Alloys by Thermal-Stress Cycling” (Mehringer, F. J., and Felgar, R. P., 1960, ASME J. Basic Eng., 82, pp. 661–670)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Cycle-Dependent Stress Relaxation of A-286 Alloy” (Ross, A. S., and Morrow, JoDean, 1960, ASME J. Basic Eng., 82, pp. 654–658)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “The Adiabatic Bulk Modulus of Normal Paraffin Hydrocarbons From Hexane to Hexadecane” (Rolling, R. E., and Vogt, C. J., 1960, ASME J. Basic Eng., 82, pp. 635–642)
(The American Society of Mechanical Engineers (ASME), 1960)