Journal of Fluids Engineering: Recent submissions
Now showing items 6001-6020 of 9024
-
A General Method for Correlating Labyrinth-Seal Leak-Rate Data
(The American Society of Mechanical Engineers (ASME), 1960)The proper selection of an optimum labyrinth seal for a given application depends upon an accurate estimate of the seal leak rate. Suitable accuracy, particularly for straight labyrinth seals, ... -
Flow Parameters in Hydrostatic Lubrication for Several Bearing Shapes
(The American Society of Mechanical Engineers (ASME), 1960)In the case of hydrostatic lubrication the designer of thrust bearings has to make decisions regarding the shape of pads, location of oil holes, and configuration of oil grooves. In this paper ... -
Discussion: “Electron Microscopy of Stress-Induced Structural Alterations Near Inclusions in Bearing Steels” (O’Brien, John L., and King, Alwyn H., 1966, ASME J. Basic Eng., 88, pp. 568–571)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “Transmission of Fluid Power by Pulsating-Flow (P-F) Concept in Hydraulic Systems” (Weng, Cheng-Kuo, 1966, ASME J. Basic Eng., 88, pp. 316–321)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “Some Physical Effects of Cavity Collapse in Liquids” (Hickling, R., 1966, ASME J. Basic Eng., 88, pp. 229–235)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “The Wall Effect in Cavity Flow” (Ai, D. K., 1966, ASME J. Basic Eng., 88, pp. 132–136)
(The American Society of Mechanical Engineers (ASME), 1966) -
Experimental Observations on the Flow Past a Plano-Convex Hydrofoil
(The American Society of Mechanical Engineers (ASME), 1966)Some new measurements and observations on the noncavitating and cavitating flow past a plano-convex hydrofoil are presented. Under some conditions of partial cavitation, strong, periodic oscillations ... -
Mechanism of Rolling in Force Contact of Elastic Bodies
(The American Society of Mechanical Engineers (ASME), 1966) -
Decay of Turbulence in Axisymmetric Wakes
(The American Society of Mechanical Engineers (ASME), 1966)Turbulent wakes formed downstream of flat, circular disks were surveyed with hot-wire anemometers in a low-speed wind tunnel. Three regions were discernible in the wake. Between the disk and x ... -
Cavitation Tests in Pipe Bends
(The American Society of Mechanical Engineers (ASME), 1966)A series of experiments on the square-section bends was performed for determining the effects of the following shape differences of the surface-pressure distributions on cavitation inception. (a) ... -
Fatigue Failure Under Complex Stress Histories
(The American Society of Mechanical Engineers (ASME), 1966)An expression for predicting fatigue failure of a structure subjected to sinusoidal stress cycles of different amplitudes and different mean values is derived. The derivation is based on a ... -
The Fluids Engineering Laboratory at the University of Michigan
(The American Society of Mechanical Engineers (ASME), 1960)Although the purpose of this paper is specifically that of describing the Fluids Engineering Laboratory at the University of Michigan, it is clear that an understanding of the faculty philosophy ... -
Condensing Vapor Lubrication of Self-Acting Long Journal Bearings
(The American Society of Mechanical Engineers (ASME), 1966)This is a theoretical investigation into the behavior of self-acting long journal bearings lubricated with vapor which may partially condense in the high-pressure region of a loaded bearing. ... -
Some Physical Effects of Cavity Collapse in Liquids
(The American Society of Mechanical Engineers (ASME), 1966)The mechanism of cavity collapse in liquids is discussed in relation to certain observed effects in the fields of cavitation damage to metals, sonoluminescence, and the nucleation of freezing ... -
Recent Research on Cascade-Flow Problems
(The American Society of Mechanical Engineers (ASME), 1966)A survey is given of extensive research work on cascade-flow problems carried out in recent years in Germany. A considerable part of this work was done in the Variable Density High Speed ... -
The Microslip Between a Ball and Its Track in Ball-Thrust Bearings
(The American Society of Mechanical Engineers (ASME), 1966)An approximate solution is proposed for the microslip between a rolling ball and its track when the ball is subjected to applied moments and forces in the plane of motion together with a ... -
Cavitation Hysteresis
(The American Society of Mechanical Engineers (ASME), 1966)In many cases, cavitation disappears at higher pressures than those at which it first appears. A measure of this cavitation hysteresis is the cavitation-delay time which tends to decrease with ... -
Theory and Experiments of Squeeze-Film Gas Bearings: Part 1—Cylindrical Journal Bearing
(The American Society of Mechanical Engineers (ASME), 1966)An asymptotic analysis for the cylindrical squeeze-film gas journal bearing has been formulated. An approximate analytical solution is presented. Load-deflection experiments have been performed on ... -
External Friction and Relationship Between Adhesion and Deformation Components
(The American Society of Mechanical Engineers (ASME), 1966)This paper deals with the friction coefficient for a plastic contact with due regard to the volume deformation of the plastic material and adhesion at the contact. Equations are derived which ... -
A Theory of Lubrication by Microirregularities
(The American Society of Mechanical Engineers (ASME), 1966)This paper describes a theory of liquid lubrication applicable to parallel surfaces, such as the surfaces of a rotary-shaft face seal. The lubrication mechanism presented is based on surface ...