Journal of Fluids Engineering: Recent submissions
Now showing items 5781-5800 of 9024
-
Flow Measurements Near a Reynolds Ridge
(The American Society of Mechanical Engineers (ASME), 1996) -
Questions in Fluid Mechanics: Tortuous Micro-Flow in Large Disordered Packed Beds
(The American Society of Mechanical Engineers (ASME), 1996) -
Turbulent-Spot Propagation in a Decelerating, Compressible Flow
(The American Society of Mechanical Engineers (ASME), 1996) -
Design of Pressurized Cylinders for High-Temperature Applications
(The American Society of Mechanical Engineers (ASME), 1960)General equations for the stresses in a thick-walled cylinder in a state of plane strain are derived considering “steady-state” creep. A specific form of the creep-rate function is assumed and ... -
Similarity Solution for a Turbulent Round Jet
(The American Society of Mechanical Engineers (ASME), 1996) -
Review—Advances in Three-Dimensional Turbulent Boundary Layers With Emphasis on the Wall-Layer Regions
(The American Society of Mechanical Engineers (ASME), 1996)Current information concerning three-dimensional turbulent boundary layers is discussed. Several topics are presented including (i) a detailed description of eleven experiments published since 1990. ... -
Sequential Production of mm-Sized Spherical Shells in Liquid-Liquid Gas Systems
(The American Society of Mechanical Engineers (ASME), 1996)A new device has been developed for sequential production of mm-sized solid spherical shells using liquid-liquid gas systems. This device comprises a cylindrical vessel, for containing two kinds ... -
A Novel Pump for MEMS Applications
(The American Society of Mechanical Engineers (ASME), 1996) -
Perspective: The Experimentalist and the Problem of Turbulence in the Age of Supercomputers
(The American Society of Mechanical Engineers (ASME), 1996)Due to the rising capabilities of computational fluid mechanics (CFD), the role of the experimentalist in solving the problem of turbulence has come under serious question. However, after much ... -
Handbook of Fluid Dynamics and Fluid Machinery
(The American Society of Mechanical Engineers (ASME), 1996) -
Particle-Surface Interactions in Heat Exchanger Fouling
(The American Society of Mechanical Engineers (ASME), 1996)The problem of fouling is of vital importance to heat exchanger efficiency and should be considered during the design phase of the heat exchanger. The purpose of the present paper is to ... -
A Nonlinear Calculation of Rotating Cavitation in Inducers
(The American Society of Mechanical Engineers (ASME), 1996)In the previous linear analysis (Tsujimoto et al., 1993) it was found that there can be a backward rotating cavitation as well as a forward mode which rotates faster than impeller. Although ... -
Free-Surface Wave-Induced Separation
(The American Society of Mechanical Engineers (ASME), 1996)Free-surface wave-induced separation is studied for a surface-piercing NACA 0024 foil over a range of Froude numbers (0, .2, .37, .55) through computational fluid dynamics of the unsteady ... -
Measurements of the Velocity Field Downstream of an Impeller
(The American Society of Mechanical Engineers (ASME), 1996)The velocity field downstream of a model impeller operating in water was measured using a two-component laser doppler velocimeter. The investigation focussed on the spatial development of the ... -
Three-Dimensional Analysis of Partially Open Butterfly Valve Flows
(The American Society of Mechanical Engineers (ASME), 1996)A numerical simulation of butterfly valve flows is a useful technique to investigate the physical phenomena of the flow field. A three-dimensional numerical analysis was carried out on incompressible ... -
Angular Bias Errors in Three-Component Laser Velocimeter Measurements
(The American Society of Mechanical Engineers (ASME), 1996)For three-component laser velocimeter systems, the change in projected area of the coincident measurement volume for different flow directions will introduce an “angular” bias in naturally sampled ... -
Possibility of Quantitative Prediction of Cavitation Erosion Without Model Test
(The American Society of Mechanical Engineers (ASME), 1996)A scenario for quantitative prediction of cavitation erosion was proposed. The key value is the impact force/pressure spectrum on a solid surface caused by cavitation bubble collapse. As the ... -
Viscosity Correction Factor for Rotameter
(The American Society of Mechanical Engineers (ASME), 1996)This paper describes how the developed formula for rotameter flow coefficient using the rotameter scale provided by a manufacturer and valid for a specific fluid and for design (or calibration) ... -
Dynamic Response of Ducted Bubbly Flows to Turbomachinery-Induced Perturbations
(The American Society of Mechanical Engineers (ASME), 1996)The present work investigates the dynamics of the three-dimensional, unsteady flow of a bubbly mixture in a cylindrical duct subject to a periodic pressure excitation at one end. One of the ... -
Flow Resistance Correlation of Wire Nets in a Wide Range of Reynolds Numbers for Thermal Design of Electronic Equipment
(The American Society of Mechanical Engineers (ASME), 1996)