Journal of Fluids Engineering: Recent submissions
Now showing items 5241-5260 of 9024
-
Discussion: “A Format Method for Generating Liapunov Functions” (Peczkowski, J. L., and Liu, R. W., 1967, ASME J. Basic Eng., 89, pp. 433–439)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “Linearization of Time-Independent Nonlinearities by Use of an Extra Signal and Extra Nonlinearity” (Oldenburger, R., and Ikebe, Y., 1967, ASME J. Basic Eng., 89, pp. 241–249)
(The American Society of Mechanical Engineers (ASME), 1967) -
Dynamic Reversibility in Fluid Flows
(The American Society of Mechanical Engineers (ASME), 1967)This note points out the relatively simple character of dynamically reversible flows. A flow is said to be dynamically reversible if the reversed flow is possible under the action of suitable ... -
Remarks on an Existing Numerical Method to Estimate the Stress Intensity Factor of a Straight Crack in a Finite Plate
(The American Society of Mechanical Engineers (ASME), 1967) -
A Note on Static Hole Errors
(The American Society of Mechanical Engineers (ASME), 1967) -
Discharge Coefficients and Steady-State Flow Forces for Hydraulic Poppet Valves
(The American Society of Mechanical Engineers (ASME), 1960)Experiments were run on a poppet valve operating in hydraulic oil. The experimental values of the flow forces and discharge coefficients were about 25 per cent below the predicted theoretical ... -
Flow Separation and Redevelopment Downstream of an End-Cap Orifice in a Tube
(The American Society of Mechanical Engineers (ASME), 1967) -
Flow Regime Identification in Horizontal Channels With Different Types of Rod Clusters
(The American Society of Mechanical Engineers (ASME), 1998) -
Discussion: “Supersonic Jet Noise Reductions Predicted With Increased Jet Spreading Rate” (Dahl, M. D., and Morris, P. J., 1998, ASME J. Fluids Eng., 120, pp. 471–476)
(The American Society of Mechanical Engineers (ASME), 1998) -
Richardson’s Annular Effect in Oscillating Laminar Duct Flows
(The American Society of Mechanical Engineers (ASME), 1998) -
Asymptotic Flow Regimes in Pulsatile Flows of Bingham Plastics
(The American Society of Mechanical Engineers (ASME), 1998) -
Laser Pointing Stability and Alignment Technique
(The American Society of Mechanical Engineers (ASME), 1998) -
Editorial
(The American Society of Mechanical Engineers (ASME), 1998) -
Discussion: “Three-Dimensional Laminar Flow in a Rotating Multiple-Pass Square Channel With Sharp 180-Deg Turns” (Hwang, Jenn-Jiang, and Hai, Dong-Yuo, 1998, ASME J. Fluids Eng., 120, pp. 488–495)
(The American Society of Mechanical Engineers (ASME), 1998) -
Features and Results of Several Programs of Radiation-Damage Surveillance of Power Reactor Pressure Vessels
(The American Society of Mechanical Engineers (ASME), 1967)The meaning and purpose of reactor pressure vessel surveillance is briefly discussed. Features of the surveillance programs in the Yankee, Big Rock Point, SM-1, and SM-1A reactors are briefly ... -
Alternate Eddy Shedding Set Up by the Nonaxisymmetric Recirculation Zone at the Exhaust of a Cyclone Dust Separator
(The American Society of Mechanical Engineers (ASME), 1998)Two cyclone dust separators with geometric swirl numbers of 3.324 and 3.043 were used to analyze the motion of the complex three-dimensional time dependent motion set up in the free exhaust. ... -
An Experimental Study of Swirling Flow Pneumatic Conveying System in a Vertical Pipeline
(The American Society of Mechanical Engineers (ASME), 1998)A swirling flow is adopted for a vertical pneumatic conveying system to reduce conveying velocity, pipe wear, and particle degradation. An experimental study has addressed the characteristics of ... -
Quantitative Evaluation of Cavitation Erosion
(The American Society of Mechanical Engineers (ASME), 1998)In order to evaluate the quantitative cavitation-erosion resistance of materials, a pressure-detector-installed specimen was developed, which can measure both the impact load produced by cavitation ... -
Refractive-Index-Matching Laser Velocimetry for Complex, Isothermal Flows
(The American Society of Mechanical Engineers (ASME), 1998)Refractive-Index-Matching Laser Velocimetry (RIMLV) obtains velocity distributions inflow through complex geometries. Laser velocimetry is used to measure the flow of a constant-temperature mixture ... -
One-Dimensional Bubbly Cavitating Flows Through a Converging-Diverging Nozzle
(The American Society of Mechanical Engineers (ASME), 1998)A nonbarotropic continuum bubbly mixture model is used to study the one-dimensional cavitating flow through a converging-diverging nozzle. The nonlinear dynamics of the cavitation bubbles are ...