Journal of Fluids Engineering: Recent submissions
Now showing items 4621-4640 of 9024
-
Development of a Steady Vortex Generator Jet in a Turbulent Boundary Layer
(The American Society of Mechanical Engineers (ASME), 2003)The development of a vortex generator jet within a turbulent boundary layer was studied by the particle image velocimetry method. Jet velocities ranging from one to three times greater than ... -
Analysis of the Flow Through a Vented Automotive Brake Rotor
(The American Society of Mechanical Engineers (ASME), 2003)Particle image velocimetry (PIV) was used to measure air velocities through a high solidity radial flow fan utilized as an automotive vented brake rotor. A brake rotor is a somewhat unusual ... -
Swing Check Valve Characterization and Modeling During Transients
(The American Society of Mechanical Engineers (ASME), 2003)The hydraulic torque on the disk of a swing check valve strongly influences the dynamic valve-fluid interaction. This torque is difficult to quantify. In this study, the hydraulic torque is ... -
Filling Process in an Open Tank
(The American Society of Mechanical Engineers (ASME), 2003)A numerical simulation for a filling process in an open tank is performed in this paper. A single set of governing equations is employed for the entire physical domain covering both water ... -
Numerical Simulations of Flows Inside a Partially Filled Centrifuge
(The American Society of Mechanical Engineers (ASME), 2003)A numerical study was conducted to predict the dynamics of gas/liquid flows in a partially filled cylinder undergoing moderate to rapid rotation. Two specific problems were considered: spinup ... -
The Structure of Wall-Impinging Jets: Computed Versus Theoretical and Measured Results
(The American Society of Mechanical Engineers (ASME), 2003)In this work, the structure of computed wall-impinging gas jets is compared with theoretical and experimental results presented in the literature. The computational study employs the k-ε model ... -
Magnetohydrodynamic Viscous Flow Separation in a Channel With Constrictions
(The American Society of Mechanical Engineers (ASME), 2003)An analysis is made of the flow of an electrically conducting fluid in a channel with constrictions in the presence of a uniform transverse magnetic field. A solution technique for governing ... -
Phase-Averaged Velocity Field Measurements of Flow Around an Isolated Axial-Fan Model
(The American Society of Mechanical Engineers (ASME), 2003)The phase-averaged flow characteristics around a forward-swept axial fan model were investigated using a two-frame PTV method. The velocity fields in the sagittal and axial planes show clearly ... -
Numerical Simulation of Two-Phase Flow in Injection Nozzles: Interaction of Cavitation and External Jet Formation
(The American Society of Mechanical Engineers (ASME), 2003)The present investigation demonstrates the strong interaction of cavitating nozzle flow with the outside jet formation. Due to the strong sensitivity of cavitation on the imposed boundary conditions, ... -
Experimental and Numerical Studies in a Centrifugal Pump With Two-Dimensional Curved Blades in Cavitating Condition
(The American Society of Mechanical Engineers (ASME), 2003)In the presented study a special test pump with two-dimensional curvature blade geometry was investigated in cavitating and noncavitating conditions using different experimental techniques and a ... -
The Stretching of a Viscoplastic Thread of Liquid
(The American Society of Mechanical Engineers (ASME), 2003)The problem of stretching a viscoplastic (yield-stress) thread of a liquid hanging vertically is considered. The length of the thread at later times and the time at which it ruptures is ... -
High-Frequency Ultrasonic Atomization With Pulsed Excitation
(The American Society of Mechanical Engineers (ASME), 2003)Ultrasonic atomization is a very convenient method to produce sprays of very small droplets. Resulting droplet size distributions are very narrow and the mean diameter is essentially only ... -
Discussion: “Two Models for Cavity Flow, a Theoretical Summary and Application” (Street, R. L., and Larock, B. E., 1968, ASME J. Basic Eng., 90, pp. 269–274)
(The American Society of Mechanical Engineers (ASME), 1968) -
Discussion: “Bubble Trajectories and Equilibrium Levels in Vibrated Liquid Columns” (Foster, J. M., Botts, J. A., Barbin, A. R., and Vachon, R. I., 1968, ASME J. Basic Eng., 90, pp. 125–132)
(The American Society of Mechanical Engineers (ASME), 1968) -
Discussion: “Two and Three-Dimensional Fluid Transients” (Streeter, V. L., and Wylie, E. B., 1968, ASME J. Basic Eng., 90, pp. 501–509)
(The American Society of Mechanical Engineers (ASME), 1968) -
Discussion: “Turbulent Flow of Dilute Aqueous Polymer Solutions” (Goren, Y., and Norbury, J. F., 1967, ASME J. Basic Eng., 89, pp. 814–822)
(The American Society of Mechanical Engineers (ASME), 1968) -
Discussion: “The Stability of a Simple Surge Tank” (Duggins, R. K., 1968, ASME J. Basic Eng., 90, pp. 97–102)
(The American Society of Mechanical Engineers (ASME), 1968) -
Discussion: “The Behavior of a Spherical Bubble in the Vicinity of a Solid Wall” (Shima, A., 1968, ASME J. Basic Eng., 90, pp. 75–89)
(The American Society of Mechanical Engineers (ASME), 1968) -
Pressure Drop in Capillary Slug Flow
(The American Society of Mechanical Engineers (ASME), 1968) -
A Note on the Saint-Venant Theory of Failure
(The American Society of Mechanical Engineers (ASME), 1968)