Journal of Fluids Engineering: Recent submissions
Now showing items 1821-1840 of 9024
-
Dynamics of Large Buoyant Clouds Generated by Rocket Launches
(The American Society of Mechanical Engineers (ASME), 1972)Motion pictures of launches of Titan III solid rocket motors were used, in conjunction with conservation equations and knowledge of rocket plume properties, to determine the initial temperature ... -
Flow Angle and Shear Stress Measurements Using Heated Films and Wires
(The American Society of Mechanical Engineers (ASME), 1972)The heat transfer characteristics of yawed slender filaments have been generalized to include pairs of heated-film skin friction gages, as well as conventional hot wire probes, New sensor designs ... -
The Fluid Mechanics of Multiple-Venturi Systems and Their Application to Flow-Rate Metering
(The American Society of Mechanical Engineers (ASME), 1972)The concept of a multiple-venturi system is applied to the design of a flow-rate meter. This meter type has the capability of offering a high signal-to-loss ratio over a broad flow range. ... -
The “Efficiency Transient Control” Concept for Optimal Load Control in Kaplan Turbine Hydroelectric Installations
(The American Society of Mechanical Engineers (ASME), 1972)In the case of Kaplan turbines the consideration of the efficiency parameter is critical from the control strategy synthesis viewpoint. As it is not essential in hydrosystem analysis, explicit ... -
Laminar Flow of an Incompressible Fluid in a Conduit With Arbitrary Cross Section, Arbitrary Time-Varying Pressure Gradient, and Arbitrary Initial Velocity
(The American Society of Mechanical Engineers (ASME), 1972)A computer-oriented solution is given for the flow described in the title of the paper. The boundary shape is represented by specification of the coordinates of N points on the boundary; the ... -
Application of a Cumulative Damage Concept to Fatigue
(The American Society of Mechanical Engineers (ASME), 1961)A general concept of the accumulation of damage is described. This concept is combined with a particular hypothesis for the accumulation of fatigue damage. Initial and failure conditions are ... -
Energy Spectrum and Turbulent Scales in a Circular Water Jet
(The American Society of Mechanical Engineers (ASME), 1972)The time micro and macroscales are computed from measured energy spectra in the fully developed region of a submerged circular water jet. The corresponding longitudinal scales are approximated ... -
Sensitivity of the Creep-Rupture Properties of Waspaloy Sheet to Sharp-Edged Notches in the Temperature Range 1000–1400 Deg F
(The American Society of Mechanical Engineers (ASME), 1972)Time-dependent notch sensitivity of Waspaloy was observed at test temperatures from 1000 to 1300 deg F. Its occurrence in this range was dependent on the heat treatment. “Overaging” eliminated ... -
Computerized Evaluations of the Relative Abilities of Seven Time-Temperature Parameters to Correlate and Extrapolate Nickel Alloy Stress-Rupture Data
(The American Society of Mechanical Engineers (ASME), 1972)A total of 31 stress-rupture data sets for 28 different nickel-base alloys, including 1153 individual test results, have been treated by graphical methods and computer programs to allow ... -
A Method for Predicting Creep Data for Commercial Alloys on a Correlation Between Creep Strength and Rupture Strength
(The American Society of Mechanical Engineers (ASME), 1972)In this paper a method is presented for correlating the creep and rupture strengths of a wide variety of commercial alloys. The ultimate aim of this correlation is to predict design creep ... -
Discussion: “An Analysis of Axisymmetric Turbulent Flow Past a Long Cylinder” (White, F. M., 1972, ASME J. Basic Eng., 94, pp. 200–204)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “Liquid-Vapor Interactions in a Constant-Area Condensing Ejector” (Levy, E. K., and Brown, G. A., 1972, ASME J. Basic Eng., 94, pp. 169–179)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “On Flow Past a Supercavitating Cascade of Cambered Blades” (Hsu, C. C., 1972, ASME J. Basic Eng., 94, pp. 163–168)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “Effects of Heat and Mass Transfer on Rayleigh-Taylor Instability” (Hsieh, D. Y., 1972, ASME J. Basic Eng., 94, pp. 156–160)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “Two-Phase, Two-Component Critical Flow in a Venturi” (Smith, R. V., 1972, ASME J. Basic Eng., 94, pp. 147–151)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “Nonlinear Effects in the Collapse of a Nearly Spherical Cavity in a Liquid” (Chapman, R. B., and Plesset, M. S., 1972, ASME J. Basic Eng., 94, pp. 142–145)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “An Explicit Scheme for the Calculation of Three-Dimensional Turbulent Boundary Layers” (Nash, J. F., 1972, ASME J. Basic Eng., 94, pp. 131–138)
(The American Society of Mechanical Engineers (ASME), 1972) -
Bursting of Tubular Specimens by Gaseous Detonation
(The American Society of Mechanical Engineers (ASME), 1961)The paper describes some experimental work designed to investigate the bursting of pipe and pressure vessels by gaseous detonation. The test specimens were 3.25-in-OD tubes, 12 in. long, and ... -
Discussion: “The Channel Flow of a Density-Stratified Fluid About Immersed Bodies” (Droughton, J. V., and Chen, C. F., 1972, ASME J. Basic Eng., 94, pp. 122–129)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “Two-Dimensional Diffuser Performance With Subsonic, Two-Phase, Air–Water Flow” (Hench, J. E., and Johnston, J. P., 1972, ASME J. Basic Eng., 94, pp. 105–119)
(The American Society of Mechanical Engineers (ASME), 1972)