Journal of Fluids Engineering: Recent submissions
Now showing items 1761-1780 of 9024
-
Discussion: “Inlet and Exit-Header Shapes for Uniform Flow Through a Resistance Parallel to the Main Stream” (Perlmutter, Morris, 1961, ASME J. Basic Eng., 83, pp. 361–368)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Particle Trajectories in a Gas Centrifuge” (Kriebel, A. R., 1961, ASME J. Basic Eng., 83, pp. 333–339)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Generalization of a Class of Solutions of the Laminar, Incompressible Boundary-Layer Equations” (Winer, Ward O., and Hansen, Arthur G., 1961, ASME J. Basic Eng., 83, pp. 328–332)
(The American Society of Mechanical Engineers (ASME), 1961) -
Friction Drag on Bladed Disks in Housings as a Function of Reynolds Number, Axial and Radial Clearance, and Blade Aspect Ratio and Solidity
(The American Society of Mechanical Engineers (ASME), 1961)Extra losses from partial admission operation of a gas turbine occur both in the nozzle flow arc and away from it. The latter have been related to the theory of fluid flow over a rotating ... -
Generalized Multistage Axial Compressor Characteristics
(The American Society of Mechanical Engineers (ASME), 1961)Presented below is a method of calculating the off-design performance of multistage axial compressor characteristics that differs in concept from previous methods. A set of resulting calculations ... -
The Phase-Plane Topology of the Simple Surge-Tank Equation
(The American Society of Mechanical Engineers (ASME), 1961)An investigation of the phase-plane solution curves of the nonlinear differential equation describing the motion of the water level in a simple surge tank operating in conjunction with a turbine ... -
Complete Pump Characteristics and the Effects of Specific Speeds on Hydraulic Transients
(The American Society of Mechanical Engineers (ASME), 1961)This paper presents complete pump characteristics of specific speeds 1800, 7600, and 13,500 (gpm units) in the ν – hP (flow ratio-head ratio) co-ordinate system. The method of developing these ... -
Surges in Air Vents Adjacent to Emergency Gates
(The American Society of Mechanical Engineers (ASME), 1961)This paper examines the mechanics of surges in air vents and advances methods for calculating their magnitude. Particular attention is paid to the magnitude of the backsurge which can occur ... -
Hydroelastic Vibrations of Flat Plates Related to Trailing Edge Geometry
(The American Society of Mechanical Engineers (ASME), 1961)Vortex-induced vibrations of thin flat plates are studied as a function of trailing edge geometry. In an effort to extend the analysis to a more comprehensive treatment than that provided by ... -
Nonsteady Supercritical Discharge Through an Orifice
(The American Society of Mechanical Engineers (ASME), 1961)Previous studies of shock reflection from open-ended duct configurations indicate that a steady discharge is not instantaneously formed and that the effects of this lag may occasionally be ... -
A Preliminary Study of Turbulence Characteristics of Flow Along a Corner
(The American Society of Mechanical Engineers (ASME), 1961)In the turbulent flow of a fluid along a corner, secondary flows occur which have a marked influence on the velocity distributions in planes normal to the mean flow direction. All published ... -
On the Mechanism of Cavitation Damage by Nonhemispherical Cavities Collapsing in Contact With a Solid Boundary
(The American Society of Mechanical Engineers (ASME), 1961)A perfect fluid theory, which neglects the effect of gravity, and which assumes that the pressure inside a cavitation bubble remains constant during the collapse process, is given for the case ... -
Cavitation Tests on Hydrofoils Designed for Accelerating Flow Cascade: Report 1
(The American Society of Mechanical Engineers (ASME), 1961)In previous reports, theory [1, 2] and experiments [3–7] were discussed on profiles that promised to possess desirable characteristics when incorporated into cascades of given arrangement. These ... -
An Experimental Study of Vortex Chamber Flow
(The American Society of Mechanical Engineers (ASME), 1961)It is shown that a relatively simple analysis predicts the functional variation of temperature and pressure in a vortex chamber with radius and inlet velocity. The predicted variation is in ... -
Adiabatic Flow of Flashing Liquids in Pipes
(The American Society of Mechanical Engineers (ASME), 1961)The assumption of a homogeneous fluid in thermodynamic equilibrium has frequently been made in describing the behavior of a vapor-liquid mixture flowing in constant area pipes. Although this ... -
A Flow Model for Two-Phase Slug Flow in Horizontal Tubes
(The American Society of Mechanical Engineers (ASME), 1961)The paper presents a construction of a simplified model approximating the actual observed flow pattern. The resulting expressions for frictional pressure drop are found to agree fairly well with ... -
Rolling-Contact Fatigue Studies With Four Tool Steels and a Crystallized Glass Ceramic
(The American Society of Mechanical Engineers (ASME), 1961)The rolling-contact fatigue properties of crystallized glass ceramic balls together with AISI M-1, AISI M-50, Halmo, and WB-49 alloy steel balls tempered to various hardness levels were determined ... -
Externally Pressurized Step Journal Bearings
(The American Society of Mechanical Engineers (ASME), 1961)An externally pressurized gas journal bearing which achieves its load carrying capability by utilizing flow throttling dams parallel to the direction of rotation is discussed in this paper. Test ... -
A Solution of Reynolds Equation for a Full Finite Journal Bearing
(The American Society of Mechanical Engineers (ASME), 1961)Reynolds equation for the pressure in a full finite journal bearing which is nonhomogeneous has been reduced to a homogeneous equation. By separating the variables the problem is reduced to ... -
Squeeze Films: A Finite Journal Bearing With a Fluctuating Load
(The American Society of Mechanical Engineers (ASME), 1961)A general method is derived for the solution of the Reynolds equation including the effects of tangential and normal velocities. It is applied to the solution of a full journal bearing under ...