Journal of Fluids Engineering: Recent submissions
Now showing items 1561-1580 of 9024
-
Dynamic Characteristics of Annular Fluid Transmission Lines
(The American Society of Mechanical Engineers (ASME), 1974)Automatic control of an oil well drilling process requires the knowledge of the dynamics of signal propagation through the annulus formed between the drill and the casing. This paper extends ... -
Further Computations of Supersonic Free Shear Layers
(The American Society of Mechanical Engineers (ASME), 1974) -
On the Flow Fields of Inertial Impactors
(The American Society of Mechanical Engineers (ASME), 1974)The flow field in an inertial impactor was studied experimentally with a water model by means of a flow visualization technique. The influence of such parameters as Reynolds number and ... -
An Experimental Investigation of Transition of a Plane Poiseuille Flow
(The American Society of Mechanical Engineers (ASME), 1974)The transition process of laminar flow between parallel plates is investigated experimentally. This problem has recently gained much attention with several reported works; however, the maximum ... -
Frequency Response of Fluid Lines With Turbulent Flow
(The American Society of Mechanical Engineers (ASME), 1974)A single boundary layer model to account for transient viscous effects is applied to small amplitude sinusoidally disturbed turbulent flow in a tube. The viscous dissipation is calculated using ... -
Design and Construction of a Wind Tunnel for Mass Transfer Studies in Incompressible Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1974)The apparatus of previous workers are described in order to evaluate the need for further studies of mass transfer into turbulent boundary layers. The apparatus built at the University of ... -
Vortex Formation in the Wake of a Vibrating, Flexible Cable
(The American Society of Mechanical Engineers (ASME), 1974)The von Karman vortex streets formed in the wakes of vibrating, flexible cables were studied using a hot-wire anemometer. All the experiments took place in the flow regime where the vibration ... -
A Contribution to the Numerical Solution of Developing Laminar Flow in the Entrance Region of Concentric Annuli With Rotating Inner Walls
(The American Society of Mechanical Engineers (ASME), 1974)The boundary layer simplification of the Navier-Stokes equations for hydrodynamically developing laminar flow with constant physical properties in the entrance region of concentric annuli with ... -
Experiments on the Resistance Law for Non-Darcy Compressible Gas Flows in Porous Media
(The American Society of Mechanical Engineers (ASME), 1974)Experiments were performed to examine the resistance law for non-Darcy compressible gas flow through a porous material. A particular objective of the investigation was to determine whether a ... -
Analysis of Pressure Wave Reflection in the Male Urethra for the Purpose of Diagnosing Obstructions
(The American Society of Mechanical Engineers (ASME), 1974)This paper investigates the feasibility of diagnosing intraurethral obstructions in males by means of a pressure pulse technique. Initial discussion centers on some of the anatomical and physiological ... -
Japanese Report: An Advanced Design Method for Pump/Turbines
(The American Society of Mechanical Engineers (ASME), 1974) -
Calculation of the Development of Turbulent Boundary Layers With a Turbulent Freestream
(The American Society of Mechanical Engineers (ASME), 1974)An existing integral boundary layer calculation procedure is modified to predict turbulent boundary layers developing in a turbulent freestream. Extra terms in both the turbulence model equation ... -
Modeling of Flow-Induced Vibrations in Heat Exchangers and Nuclear Reactors
(The American Society of Mechanical Engineers (ASME), 1974)This paper discusses the appropriate scaling factors for the modeling of the fluid-mechanical interaction of complex structures. The possible mechanisms of flow-excited vibration are described, and ... -
On the Fluid Mechanics of the Inherent Restrictor
(The American Society of Mechanical Engineers (ASME), 1974)Hydrostatic thrust bearings commonly employ a sharp-edged asymmetric inlet, generally referred to as an inherent restrictor. For gas and liquid metal bearings, this inlet configuration offers ... -
Critical Reviews
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Improved Expansion Factors for Nozzles, Orifices, and Variable-Area Meters” (Head, Victor B., 1974, ASME J. Fluids Eng., 96, pp. 150–157)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “On the Viscous Drag on a Rotating Disk” (Gu, A., 1974, ASME J. Fluids Eng., 96, pp. 184–186)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “The Hydraulic Analogy Applied to Nonsteady, Two-Dimensional Flow in the Partial-Admission Turbine” (Heen, Helge K., and Mann, Robert W., 1961, ASME J. Basic Eng., 83, pp. 408–419)
(The American Society of Mechanical Engineers (ASME), 1961) -
Preliminary Design of a Roll-Stabilization System for a Ship
(The American Society of Mechanical Engineers (ASME), 1961)The roll stabilization of a ship with servo-operated fins is analyzed as a system problem from the viewpoint of a control engineer. The preliminary design of a roll-damping system for a ... -
Improvement of the Power Efficiency of a Hydraulic Control System by the Use of a Gain Compensated Control Valve
(The American Society of Mechanical Engineers (ASME), 1961)