Journal of Fluids Engineering: Recent submissions
Now showing items 1501-1520 of 9024
-
Flow Regime Definition for Flow Between Corotating Disks
(The American Society of Mechanical Engineers (ASME), 1974)Experimental data and results are presented for the flow of an incompressible Newtonian fluid, with full admission, between closely spaced corotating disks, and for both radially inward and ... -
Experimental Investigation of the Vortex Street Generated by a Plane Jet in a Counter Flow
(The American Society of Mechanical Engineers (ASME), 1974)Exploratory studies have indicated the existence of periodic oscillations associated with vortex street formation for a two-dimensional plane jet in a counter flowing stream. Potentially this ... -
Field Investigation and Reduction of Wicket Gate Vibration in a Francis-Type Reversible Pump/Turbine
(The American Society of Mechanical Engineers (ASME), 1974)The profiles of three wicket gates on a Francis-type reversible pump/turbine were modified in the field to reduce vibration levels in the pumping and generating modes of operation. This paper ... -
Similarity Solutions for the Interaction of a Potential Vortex With Free Stream Sink Flow and a Stationary Surface
(The American Society of Mechanical Engineers (ASME), 1974)Similarity equations, using an assumed transformation which reduces the partial differential equations to sets of ordinary differential equations, are obtained from the boundary layer and the ... -
Nozzle Discharge Coefficients—Compressible Flow
(The American Society of Mechanical Engineers (ASME), 1974)Using Walz’s approximation method for boundary layer calculation, along with a one-dimensional treatment of the compressible inviscid core flow, discharge coefficients for small nozzle to pipe ... -
A Modern Laboratory for Hydraulic Turbine and Pump/Turbine Model Performance Testing
(The American Society of Mechanical Engineers (ASME), 1974)Increased demands for higher performance, reliability, and versatility from hydraulic turbines and pump/turbines have dictated that manufacturers improve their model testing facilities to thoroughly ... -
A Note on the Unsteady Cavity Flow in a Tunnel
(The American Society of Mechanical Engineers (ASME), 1974)The unsteady internal cavitating flow such as the one observed in a pump or a turbine is studied for a simple two-dimensional model of a base-cavitating wedge in an infinite tunnel and it ... -
Improvement of the Performance of Conical Diffusers by Vortex Generators
(The American Society of Mechanical Engineers (ASME), 1974)Vortex generators, which consist of small blades, are applied to conical diffusers the divergence angles of which are 8, 12, 16, 20, and 30 deg, respectively. The area ratio of each diffuser ... -
Discussion: “An Upper Bound on the Stress in Plane Couette Flow” (Nickerson, E. C., 1973, ASME J. Fluids Eng., 95, pp. 528–532)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Turbulent Viscosities for Swirling Flow in a Stationary Annulus” (Scott, C. J., and Rask, D. R., 1973, ASME J. Fluids Eng., 95, pp. 557–566)
(The American Society of Mechanical Engineers (ASME), 1974) -
An Experimental Investigation of the Transitory Stall Regime in Two-Dimensional Diffusers
(The American Society of Mechanical Engineers (ASME), 1974)A study of flow behavior of transitory stall in two-dimensional diffusers at low Mach numbers is reported. The changes in flow patterns from stall inception to full-stall are described; the ... -
Discussion: “Cryptosteady-Flow Energy Separation” (Foa, J. V., 1973, ASME J. Fluids Eng., 95, pp. 513–518)
(The American Society of Mechanical Engineers (ASME), 1974) -
Similarity Relations for Pressure Distributions on Slot Type Rough Walls Under Turbulent Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1974) -
2000 Years More Oil!
(The American Society of Mechanical Engineers (ASME), 1974) -
On the Viscous Drag on a Rotating Disk
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Leakage and Frictional Characteristics of Turbulent Helical Flow in Fine Clearance” (Bilgen, E., Boulos, R., and Akgungor, A. C., 1973, ASME J. Fluids Eng., 95, pp. 493–497)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Analysis of Flow Separation in an Annular Expansion—Contraction With Inner Cylinder Rotating” (Dailey, G. F., and Geiger, G. E., 1973, ASME J. Fluids Eng., 95, pp. 485–492)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Turbulent Jets in a Confined Crossflow” (Stoy, R. L., and Ben-Haim, Y., 1973, ASME J. Fluids Eng., 95, pp. 551–556)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Viscous Effects in the Inception of Cavitation on Axisymmetric Bodies” (Arakeri, V. H., and Acosta, A. J., 1973, ASME J. Fluids Eng., 95, pp. 519–527)
(The American Society of Mechanical Engineers (ASME), 1974) -
Fluid Dynamics of Particle (Platelet) Deposition for Filtering Walls: Relationship to Atherosclerosis
(The American Society of Mechanical Engineers (ASME), 1974)Particle deposition onto filtering surfaces is expected to occur when the drag force of filtration overcomes the fluid mechanic wall repulsive force. A nondimensional particle deposition parameter ...