Journal of Manufacturing Science and Engineering: Recent submissions

Now showing items 7601-7620 of 7723

    • The Slack in a Stretched Thin Foil Bent Against Two Parallel Cylinders 

      A. Eshel (The American Society of Mechanical Engineers (ASME), 1975)
      A stretched finite stiffness foil bent against two parallel cylinders is approximately analyzed. The difference between its length and that of a perfectly flexible foil under similar conditions, ...

    • System Identification of the Machining Process 

      D. A. Milner (The American Society of Mechanical Engineers (ASME), 1975)
      This paper describes an identification method for determining the transfer function of a system by the use of a computer program. Frequency response data is obtained by the use of a Digital ...

    • Analysis of In-Process Buffers for Multi-Input Manufacturing Systems 

      S. S. Law; R. J. Baxter; G. M. Massara (The American Society of Mechanical Engineers (ASME), 1975)
      A model for multi-input manufacturing systems with in-process buffers is introduced based upon the concepts of system and subsystem reliability. A set of parameters is proposed for evaluating ...

    • The Role of Grain Tip Radius in Fine Grinding 

      G. K. Lal; M. C. Shaw (The American Society of Mechanical Engineers (ASME), 1975)
      The scratches produced by single abrasive grains in overcut fly milling show that the transverse shape of a grain is closely approximated by an arc of a circle. This radius of curvature is ...

    • Confirmation of the Critical Speed Stability Theory for Symmetrical Circular Saws 

      C. D. Mote; S. Holoyen (The American Society of Mechanical Engineers (ASME), 1975)
      The critical speed theory for circular saws predicts conditions of stability when a saw remains plane and cuts a straight path, and conditions of instability when the saw is no longer plane ...

    • The Anisotropic Cutting Behavior of Free-Machining Steels 

      D. R. Poirier; A. P. Kieras (The American Society of Mechanical Engineers (ASME), 1975)
      A determination of the anisotropy in the shear strength during machining of a group of free-machining steels including 1117, 11L17, and 1215 and a plain steel, 1018, is presented. The three ...

    • The Quadratic Curve and the Trajectory in the Shear Zone in Metal Cutting 

      J. H. L. The (The American Society of Mechanical Engineers (ASME), 1975)
      The quadratic curve was investigated as an approximation of the streamline in the steady-state shear zone during metal cutting. Experimentally, a very fine grid of parallel lines (spacing 25 ...

    • Damping at Metallic Interfaces Subjected to Oscillating Tangential Loads 

      P. F. Rogers; G. Boothroyd (The American Society of Mechanical Engineers (ASME), 1975)
      The results of experiments are described where the energy loss per cycle occurring at a flat metallic interface subjected to oscillating tangential loads is measured. The effects of the magnitudes ...

    • Steady-State Thermal Stresses in Wedge-Shaped Cutting Tools 

      P. F. Thomason (The American Society of Mechanical Engineers (ASME), 1975)
      Closed form expressions for the steady-state thermal stresses in a π/2 wedge, subject to constant-temperature heat sources on the rake and flank contact segments, are obtained from a conformal ...

    • Material Removal by High-Pressure Liquid Jets at Ten Kilobars 

      K. F. Neusen; E. C. LaBrush (The American Society of Mechanical Engineers (ASME), 1975)
      High-energy-density jets (0.75 × 106 hp/in.2 ) resulting from expanding liquid at extremely high pressures are capable of removing solid material from a wide variety of targets. Liquid jets ...

    • A Possible Mechanism for Causing Eccentricity in Sleeved Backup Rolls on Cold-Rolling Mills 

      E. J. Patula (The American Society of Mechanical Engineers (ASME), 1975)
      A theoretical analysis has shown that axial slipping of the sleeve on the roll arbor rather than plastic deformation of the roll necks may be the cause of backup-roll eccentricity on cold-rolling ...

    • Effects of Variable Thermal Properties on Moving-Band-Source Temperatures 

      J. Isenberg; S. Malkin (The American Society of Mechanical Engineers (ASME), 1975)
      Temperatures calculated by moving-heat-source theory for machining and sliding processes are often sufficiently large that the assumption of temperature-independent thermal properties is invalid. In ...

    • The Anchor-Last Deployment Problem for Inextensible Mooring Lines 

      Robert C. Rupe; Robert W. Thresher (The American Society of Mechanical Engineers (ASME), 1975)
      A lumped mass numerical model was developed which predicts the dynamic response of an inextensible mooring line during anchor-last deployment. The mooring line was modeled as a series of ...

    • An Analysis of a Stationary Pneumatic Wave-Energy Converter 

      Michael E. McCormick (The American Society of Mechanical Engineers (ASME), 1975)
      A theoretical analysis of a stationary pneumatic wave-energy conversion device is presented. Results obtained from the analysis show that the power converted is proportional to the cube of the ...

    • Pressure Distribution and Belt Deformation in V-Belt Drives 

      B. G. Gerbert (The American Society of Mechanical Engineers (ASME), 1975)

    • Stress Concentration in Crowned Rollers 

      K. P. Singh; B. Paul (The American Society of Mechanical Engineers (ASME), 1975)
      The edges of rollers in needle and roller bearings are crowned (i.e., rounded) in order to prevent large stress concentrations. At present, the crowning radius is determined empirically. In ...

    • On the Probabilistic Distributions of Stress and Strength in Design Problems 

      My Dao-Thien; M. Massoud (The American Society of Mechanical Engineers (ASME), 1975)
      This paper presents an approach to obtain the stress and strength density distributions in reliability design problems. The density and cumulative distributions of the stress and strength are ...

    • Two Jeffcott-Based Modal Simulation Models for Flexible Rotating Equipment 

      Dara W. Childs (The American Society of Mechanical Engineers (ASME), 1975)
      Two transient modal simulation models are presented based on the Jeffcott-Green flexible-rotor formulation. One of the models is based on the conventional “non-spinning” formulation, while the ...

    • Optimal Design of a Reflected-Core Nuclear Reactor 

      F. Y. Lam; M. A. Townsend (The American Society of Mechanical Engineers (ASME), 1975)
      Optimal results are presented for the design of a reflected-core spherical reactor. Complete model development is given. The result is a highly nonlinear system with 2 equality and 13 inequality ...

    • Deep Submergence Spherical Shell Window Assembly With Glass or Transparent Ceramic Windows for Abyssal Depth Service 

      J. D. Stachiw (The American Society of Mechanical Engineers (ASME), 1975)
      A total of 20 spherical shell windows with R0 = 4 in., Ri = 3 in., and 150 deg included spherical angle have been pressure tested under static and dynamic loading conditions. The tests ...