Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 7461-7480 of 7723
-
Application of the Deformation Theory of Plasticity for Determining Elastoplastic Stress and Strain Concentration Factors
(The American Society of Mechanical Engineers (ASME), 1976)The deformation theory of plasticity is considered as a means for obtaining a solution to the problem of calculating stress and strain concentration factors at geometric discontinuities where ... -
The Mechanical State of the Sublayer of a Surface Generated by Chip-Removal Process—Part 1: Cutting With a Sharp Tool
(The American Society of Mechanical Engineers (ASME), 1976)The mechanical state of a machined component surface was studied and three quantitative measures, namely, apparent strain energy density, strain hardening index, and residual stress distribution ... -
Tubesheet Design in U-Tube Exchangers Including the Effect of Tube Rotational Restraint
(The American Society of Mechanical Engineers (ASME), 1976)A clamped, circular plate under uniform pressure simulating a U-tube heat exchanger tubesheet is studied to ascertain the effect of tube rotational restraint on the tubesheet design. This effect ... -
Instabilities of an Asymmetric Rotor With Asymmetric Shaft Mounted on Symmetric Elastic Supports
(The American Society of Mechanical Engineers (ASME), 1976)Instabilities of an asymmetric rotor with asymmetric shaft mounted on symmetric elastic supports are considered. The periodic coefficients which appear in the system equations are eliminated by ... -
Failure Analysis of a Redundant Reeving Hoist
(The American Society of Mechanical Engineers (ASME), 1976)An analysis is presented of a reeving arrangement suitable for the hoisting of critical materials requiring fail-safe criteria. The system consists of two independent wire ropes symmetrically ... -
The Mechanical State of the Sublayer of a Surface Generated by Chip-Removal Process—Part 2: Cutting With a Tool With Flank Wear
(The American Society of Mechanical Engineers (ASME), 1976)The mechanical state of a surface machined with a tool having flank wear is discussed in this paper, which is the second in a sequence of two papers, the first dealing with sharp tools. A ... -
Product Design Implications of New High-Speed Milling Techniques
(The American Society of Mechanical Engineers (ASME), 1976)The results of recent research into ultra high-speed milling production will revolutionize machine tool design concepts and associated technical-economic study parameters. Testing demonstrated major ... -
A Singularity Approach to Circular Plates
(The American Society of Mechanical Engineers (ASME), 1976)Axisymmetric circular plate solutions can be found in several references. A designer, in using the classical technique must, for the most part, consider loading functions not continuous over the ... -
Methods for Improving the Knuckle Boom Capacity in Truck-Mounted Cranes
(The American Society of Mechanical Engineers (ASME), 1976)Presented herein are two different concepts for improving the knuckle boom capacity of truck-mounted cranes. The first concept deals with an improved Planar four-bar linkage using the two-position ... -
Criteria for Evaluating Bolt Head Design
(The American Society of Mechanical Engineers (ASME), 1976)The emphasis on reducing fastener weight, conserving material, and providing joint integrity has increased the importance of understanding the causes of bolt failure. In bolt design, a significant ... -
Attritious Wear of Silicon Carbide
(The American Society of Mechanical Engineers (ASME), 1976)Attritious wear of silicon carbide in simulated grinding tests against a cobalt base superalloy at high speed and extremely small feed rate was studied using a scanning electron microscope (SEM) ... -
Analysis of Flexible Rotor Whirl and Whip Using a Realistic Hydrodynamic Journal Bearing Model
(The American Society of Mechanical Engineers (ASME), 1976)An analytical method has been developed for the simulation of the transient and steady-state response of flexible rotors supported by realistic incompressible-film hydrodynamic journal bearings. ... -
Discussion: “The Mechanical State of the Sublayer of a Surface Generated by Chip-Removal Process—Part 1: Cutting With a Sharp Tool” (Liu, C. R., and Barash, M. M., 1976, ASME J. Eng. Ind., 98, pp. 1192–1199)
(The American Society of Mechanical Engineers (ASME), 1976) -
Metal Flow in Two-Die Swaging
(The American Society of Mechanical Engineers (ASME), 1976)A study of materials subjected to reductions in area by two-die swaging shows that non-uniform hardening occurs. The amount of cold work strengthening on the surface is the same as that for ... -
Erratum: “A Note on Blade Loss Dynamics of Rotor-Bearing Systems” (Journal of Engineering for Industry, 1976, 98, pp. 497–504)
(The American Society of Mechanical Engineers (ASME), 1976) -
Dynamic Stability of Timoshenko Beams by Finite Element Method
(The American Society of Mechanical Engineers (ASME), 1976)A Finite Element model is developed for the stability analysis of Timoshenko beam subjected to periodic axial loads. The effect of the shear deformation on the static buckling loads is studied ... -
Discussion: “An Investigation of Computer Control of Machining Chatter” (Subramanian, T. L., DeVries, M. F., and Wu, S. M., 1976, ASME J. Eng. Ind., 98, pp. 1209–1213)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Dynamic Stability of Timoshenko Beams by Finite Element Method” (Thomas, J., and Abbas, B. A. H., 1976, ASME J. Eng. Ind., 98, pp. 1145–1149)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Analysis of Flexible Rotor Whirl and Whip Using a Realistic Hydrodynamic Journal Bearing Model” (Myrick, Jr., S. T., and Rylander, H. G., 1976, ASME J. Eng. Ind., 98, pp. 1135–1143)
(The American Society of Mechanical Engineers (ASME), 1976) -
Speedy Design of Helical Compression Springs by Nomography Method
(The American Society of Mechanical Engineers (ASME), 1975)This paper introduces a few new equations and a performance nomogram for the design of helical compression springs. The procedures for calculation are simple, speedy, and accurate.