Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 7341-7360 of 7723
-
Cutting Rate-Tool Life Characteristic Functions for Material Removal Processes—Part 1: Theory
(The American Society of Mechanical Engineers (ASME), 1976)The existence of cutting rate-tool life (R-T ) characteristic functions for material removal operations is introduced in this paper. This new concept enables a comprehensive development of a ... -
A Comparison of Charpy V-Notch, Dynamic Tear, and Precracked Charpy Impact Transition-Temperature Curves for AAR Grades of Cast Steel
(The American Society of Mechanical Engineers (ASME), 1976)Impact tests using Charpy V-notch, Dynamic Tear and Precracked Charpy samples were conducted on AAR-B, AAR-C (several compositions and heat treatments), and AAR-E cast grades of steel and on a ... -
A Note on Blade Loss Dynamics of Rotor-Bearing Systems
(The American Society of Mechanical Engineers (ASME), 1976)The equations for a single-mass rotor are examined for maximum response following an impact load created by a blade loss. The close examination of the undamped system gives insight and ... -
On the Development of Multi-Edge Cutting Tools for BTA Deep-Hole Machining
(The American Society of Mechanical Engineers (ASME), 1976)The design concept and the analysis of multi-edge BTA deep-hole machining tools are presented. The main feature of the design is that the tool cutting edges are unsymmetrically located on the ... -
Cutting Rate-Tool Life Characteristic Functions for Material Removal Processes—Part 2: Verification and Applications
(The American Society of Mechanical Engineers (ASME), 1976)The experimental verification, interpretations, and applications of the concept of cutting rate-tool life (R-T) characteristic functions are presented in this paper. Two statistically designed ... -
Grinding of Glass: Surface Structure and Fracture Strength
(The American Society of Mechanical Engineers (ASME), 1976)An investigation is described of the surface structure and fracture strength for grinding of glass under various conditions. The surface structure of finished glass surfaces was examined by ... -
Grinding of Glass: The Mechanics of the Process
(The American Society of Mechanical Engineers (ASME), 1976)An investigation of the material removal process in grinding glass and the effects of the grinding process on the surface structure and fracture strength of the finished product is reported ... -
Analysis of Combined Backward-Forward Extrusion
(The American Society of Mechanical Engineers (ASME), 1976)The upper bound approach is used to analyze combined backward-forward extrusion. The deformation region is divided into five zones separated by planer and cylindrical surfaces of velocity ... -
Hot Spot Heating by Composition Shoes
(The American Society of Mechanical Engineers (ASME), 1976)It is generally understood that uneven heating of the tread of a wheel during braking is possible. A method has been devised to measure the intensity and frequency of hot spots on the wheel ... -
Verification of a One-Dimensional Two-Phase Flow Model of the Frontal Gap in Electrochemical Machining
(The American Society of Mechanical Engineers (ASME), 1976)A set of six equations, which are based on the ECM model developed by Thorpe and Zerkle, can be solved numerically to yield the one-dimensional distributions of pressure, temperature, gas ... -
The Abrasive Cut-off Operation With Oscillation
(The American Society of Mechanical Engineers (ASME), 1976)In the abrasive cut-off operation in which a thin rotating disk is plunged through a workpiece, chips must be stored as a grain traverses the entire width of work being ground. Also, heat ... -
Curvature Analysis of Surfaces in Higher Pair Contact—Part 1: An Analytical Investigation
(The American Society of Mechanical Engineers (ASME), 1976)In this paper, the analytical investigation is done to evaluate the normal and principal curvatures of contacting surfaces in higher pair contact. The velocity ratio of the members connected ... -
Static Response of Stiff-Cored Unsymmetric Sandwich Beams
(The American Society of Mechanical Engineers (ASME), 1976)Improved equations governing the deflection of an unsymmetric sandwich beam (which include the effect of extensional and bending rigidities of its stiff core) are derived using a variational ... -
Compressibility Effects in Electrochemical Machining
(The American Society of Mechanical Engineers (ASME), 1976)Based on bubbly two-phase flow an equation for the speed of sound in the ECM frontal gap is derived, and it is seen that the sonic speed is well within reach of the electrolyte velocities ... -
Curvature Analysis of Surfaces in Higher Pair Contact—Part 2: Application to Spatial Cam Mechanisms
(The American Society of Mechanical Engineers (ASME), 1976)In this paper curvature analysis is performed for different three-dimensional cam mechanisms. In every case the expressions for principal curvatures of the cam surface are given in closed forms ... -
Discussion: “A Note on Blade Loss Dynamics of Rotor-Bearing Systems” (Kirk, R. G., and Hibner, D. H., 1976, ASME J. Eng. Ind., 98, pp. 497–503)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Effects of Built-Up Edge in Drilling” (Dolodarenko, A. G., and Ham, I., 1976, ASME J. Eng. Ind., 98, pp. 287–292)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Effect of Damping on the Lateral Critical Speeds of Rotor-Bearing Systems” (De Choudhury, Pranabesh, Zsolcsak, Stephen J., and Barth, Eugene W., 1976, ASME J. Eng. Ind., 98, pp. 505–513)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Application of EHD Oil Film Theory to Industrial Gear Drives” (Wellauer, E. J., and Holloway, G. A., 1976, ASME J. Eng. Ind., 98, pp. 626–631)
(The American Society of Mechanical Engineers (ASME), 1976) -
Erratum: “Effect of Pressurization on the Vibration Isolation Capability of Squeeze Film Bearings” (Journal of Engineering for Industry, 1976, 98, pp. 109–117)
(The American Society of Mechanical Engineers (ASME), 1976)