Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 7061-7080 of 7723
-
Effects of Rotary Dressing on Grinding Wheel Performance
(The American Society of Mechanical Engineers (ASME), 1978)An investigation is described of the effects of rotary dressing on grinding wheel performance. Grinding performance is evaluated mainly in terms of the grinding forces and surface finish. It ... -
Discussion: “A Systematic Approach to the Adaptive Control of the Electro-Discharge Machining Process” (Tseng, M. M., 1978, ASME J. Eng. Ind., 100, pp. 303–309)
(The American Society of Mechanical Engineers (ASME), 1978) -
Discussion: “Identification of Machining System Dynamics by Equation Error Minimization” (Srinivasan, K., and Nachtigal, C. L., 1978, ASME J. Eng. Ind., 100, pp. 332–339)
(The American Society of Mechanical Engineers (ASME), 1978) -
Energy Requirements of the Rail Mode
(The American Society of Mechanical Engineers (ASME), 1978)The results of computer simulations of railroad operations to determine the energy required to pull freight and passenger trains over mountainous and flat profiles is presented. The effect of ... -
Disk and Strip Forging with Side Surface Foldover—Part 2: Evaluation of the Upper-Bound Solutions
(The American Society of Mechanical Engineers (ASME), 1978)The upper-bound solutions developed in Part 1 are evaluated with regard to their ability to produce a lower value for required power (load, pressure, or work). Comparisons made with existing ... -
Machining Economics and Tool Life Variation—Part 2: Application to Models for Machining Processes
(The American Society of Mechanical Engineers (ASME), 1978)A simple machining operation is modeled according to some management choices by stochastic simulation, taking into account two main tool failure mechanisms. Under the assumption that premature ... -
Chipping and Breakage of Carbide Tools
(The American Society of Mechanical Engineers (ASME), 1978)The paper deals with chipping and breakage of carbide tools and it is based on a combination of turning tests, examination of fracture surfaces, and analysis of stresses in the tool as ... -
Disk and Strip Forging with Side-surface Foldover—Part 1: Velocity Field and Upper-Bound Analysis
(The American Society of Mechanical Engineers (ASME), 1978)With the assumptions of a Mises’ rigid, perfectly-plastic material and constant shear stress friction prevailing between the forge platens and deforming solid, the upper-bound analysis technique ... -
A Numerical Method For Simultaneous Prediction of Metal Flow and Temperatures in Upset Forging of Rings
(The American Society of Mechanical Engineers (ASME), 1978)In this study, the interdependence between temperatures and metal flow during upset forging of rings has been investigated. An improved upper-bound analysis has been developed to predict metal ... -
An Experimental Strategy for Designing Tool Life Experiments
(The American Society of Mechanical Engineers (ASME), 1978)An investigation of the tool life experimental environment and its effect on designing tool life tests is presented. The D -optimal design criterion is introduced as a tool life experimental ... -
Machining Economics and Tool Life Variation—Part 1: Basic Considerations and their Practical Implications
(The American Society of Mechanical Engineers (ASME), 1978)The joint distributions of economic parameters corresponding to “optimum” conditions (minimum cost, and maximum production rate), as affected by a single tool wear mechanism, are analyzed and the ... -
Discussion: “Detection of Flaws in Railroad Wheels Using Acoustic Signatures” (Nagy, K., Dousis, D. A., and Finch, R. D., 1978, ASME J. Eng. Ind., 100, pp. 459–465)
(The American Society of Mechanical Engineers (ASME), 1978) -
High Energy Water Jet Cutting Equations for Wood
(The American Society of Mechanical Engineers (ASME), 1978)To evaluate the potential of cutting wood with high velocity water jets containing polymer additives it is necessary to develop general cutting equations that relate the cutting depth and ... -
Discussion: “Machining Economics and Tool Life Variation—Parts 1 and 2” (Levi, R., and Rossetto, S., 1978, ASME J. Eng. Ind., 100, pp. 393–401)
(The American Society of Mechanical Engineers (ASME), 1978) -
Detection of Flaws in Railroad Wheels Using Acoustic Signatures
(The American Society of Mechanical Engineers (ASME), 1978)A system for automatic inspection of railroad wheels using acoustic signatures is proposed. There is a discussion of the types of defects which need to be found. The main components of a ... -
Determination of Dynamic Characteristics of an Impact Forming Machine Structure
(The American Society of Mechanical Engineers (ASME), 1978)The noise generated from an impact forming machine arises mainly from structural vibrations and consequently accurate determination of the modal characteristics of the machine is necessary in ... -
Discussion: “Fracture and Wear as Factors Affecting Stochastic Tool-Life Models and Machining Economics” (Rossetto, S., and Levi, R., 1977, ASME J. Eng. Ind., 99, pp. 281–286)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “On the Design of Bolted Connections With Gaskets Subjected to Fatigue Loading” (Osman, M. O. M., Mansour, W. M., and Dukkipati, R. V., 1977, ASME J. Eng. Ind., 99, pp. 388–393)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Shape and Frequency Composition of Pulses From an Impact Pair” (Herbert, R. G., and McWhannell, D. C., 1977, ASME J. Eng. Ind., 99, pp. 513–518)
(The American Society of Mechanical Engineers (ASME), 1977) -
Fracture and Wear as Factors Affecting Stochastic Tool-Life Models and Machining Economics
(The American Society of Mechanical Engineers (ASME), 1977)Under production conditions cutting tools often fail under several failure modes, the occurrence of a single one only for a given operation being rather exceptional. In light of this observation ...