Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 6241-6260 of 7723
-
Determination of the Interface Heat Transfer Coefficient for Non-Isothermal Bulk-Forming Processes
(The American Society of Mechanical Engineers (ASME), 1987)Experimental and analytical techniques have been developed for the determination of the interface heat transfer coefficient for nonisothermal bulk-forming processes. A fixture consisting of two ... -
A Case Study of Cure Cycle Shrinkage Deformations
(The American Society of Mechanical Engineers (ASME), 1987)A case study of curing deformations in square struts laminated from unidirectional prepreg is presented that uses laminate and three-dimensional finite element analyses to analyze critical shrinkage ... -
Mixed Finite Element Models for Laminated Composite Plates
(The American Society of Mechanical Engineers (ASME), 1987)Mixed finite element models of the classical and shear deformation plate theories are described, and their relative advantages, disadvantages and limitations are discussed. Numerical results showing ... -
Uncertain Eigenvalue Analysis of Composite Laminated Plates by the Stochastic Finite Element Method
(The American Society of Mechanical Engineers (ASME), 1987)Uncertain eigenvalue problem of linear vibration is analyzed by means of the stochastic finite element method, the basis of which utilizes mean-centered second order perturbation technique. Attention ... -
Advanced Reliability Methods for Structural Evaluation
(The American Society of Mechanical Engineers (ASME), 1987)Approximate solutions to the general structural reliability problem, i.e., computing probabilities of complicated functions of random variables, can be obtained efficiently by the fast probability ... -
A Stochastic Model for Fatigue Crack Growth Rate Data
(The American Society of Mechanical Engineers (ASME), 1987)This paper summarizes a new approach to the probabilistic modeling of fatigue crack growth. The material’s resistance to fatigue crack growth is modeled as a stochastic process, which varies ... -
Applications of Probabilistic Finite Element Methods in Elastic/Plastic Dynamics
(The American Society of Mechanical Engineers (ASME), 1987) -
Finite Element Limitations for Orthotropic, Laminated Beam Analysis
(The American Society of Mechanical Engineers (ASME), 1987)This paper discusses the limitations of the existing finite element beam models for the analysis of orthotropic laminate beam analysis. These limitations are illustrated by comparing the existing ... -
Demonstration of a New, Fast Probability Integration Method for Reliability Analysis
(The American Society of Mechanical Engineers (ASME), 1987)The performance of a new, fast probability integration method which combines an improved equivalent normal concept and a scheme for linearizing a quadratic limit state is carefully examined. The ... -
Micromechanical Property Prediction for Flexible Matrix Composite Materials
(The American Society of Mechanical Engineers (ASME), 1987)Several closed-form solutions exit to predict elastic constants of a composite material. Most of these methods give comparable results for epoxy matrix composites, but not for flexible matrix ... -
High-Strength Tool Geometry—A Result of Research in Tool Geometry
(The American Society of Mechanical Engineers (ASME), 1964)A high-strength tool geometry has been developed as a result of research conducted in the Physical Research Department of the Cincinnati Milling Machine Company. This research was carried out ... -
Suppression of Machine Tool Chatter Using a Viscoelastic Dynamic Damper
(The American Society of Mechanical Engineers (ASME), 1987)Optimization procedures to install a viscoelastic dynamic damper into a single degree of freedom primary system is briefly reviewed. Excitation methods are shown to identify elastic modulus and ... -
Surface Roughness Measurement Using Scanning Electron Microscope with Digital Processing
(The American Society of Mechanical Engineers (ASME), 1987)Surface roughness measurement by scanning electron microscope (SEM) is investigated. The investigation was made by a digital processing technique, which follows a study by the analog method. The ... -
Verification of On-Line Computer Control of EDM by Data Dependent Systems
(The American Society of Mechanical Engineers (ASME), 1987)A new method of computer control of electro-discharge machining based on Data Dependent Systems (DDS) methodology has been recently proposed. The control is based on a parameter which effectively ... -
A Search for New Manufacturing Processes
(The American Society of Mechanical Engineers (ASME), 1964)The philosophy and methodology for a systematic, general search for new manufacturing processes is presented. Some postulated processes resulting from such a search are reviewed. -
Analysis of Hydrostatic Bulging of Anisotropic Rectangular Diaphragms by the Rigid-Plastic Finite Element Method
(The American Society of Mechanical Engineers (ASME), 1987)A variational formulation is derived for the incremental analysis of the nonsteady large deformation of normal anisotropic sheet metal which exhibits a rigid-plastic work-hardening behavior. The ... -
Contact Rigidity at Tool Shank of Turning Tools
(The American Society of Mechanical Engineers (ASME), 1987)This paper presents an experimental investigation of the contact rigidity between a turning tool shank and tool post. The contact rigidity is influenced by the flexural rigidity of tool shank, ... -
An Integrated CAD/CAPP System with “Know-hows” on Machining Accuracies of Parts
(The American Society of Mechanical Engineers (ASME), 1987)An prototype of an integrated CAD/CAPP system named CIMS has been developed. The sequence of machine tools and the machining sequence are determined by the CIMS based on the models of the ... -
The Influence of Lateral Wall Vibrations on the Ultrasonic Welding of Thin-Walled Parts
(The American Society of Mechanical Engineers (ASME), 1987)The welding of thin-walled thermoplastic parts by ultrasonic vibrations is often seriously impaired by variability in bond strength along the interface of the welded parts. This study shows that ... -
A New Tolerance Analysis Method for Designers and Manufacturers
(The American Society of Mechanical Engineers (ASME), 1987)Even when all manufactured parts for an assembly are produced within limits, these parts still may not assemble properly if the assembly tolerance analysis was inadequately performed. Naturally ...