Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5961-5980 of 7723
-
A General Optimization Model for Multi-Tool Manufacturing Systems
(The American Society of Mechanical Engineers (ASME), 1991)A machining center is a single numerically-controlled machine that incorporates several time-saving features and performs a multiplicity of operations. The life of cutting tools used in machining ... -
Computer-Aided Tolerancing, Second Edition
(The American Society of Mechanical Engineers (ASME), 1991) -
Parallelism Improvement of Ground Silicon Wafers
(The American Society of Mechanical Engineers (ASME), 1991)This paper discusses substituting grinding for lapping in machining processes of silicon wafers. To attain this goal, the rotating wafer grinding method, in which a rotating wafer is ground by ... -
Group Technology Production Methods in Manufacture
(The American Society of Mechanical Engineers (ASME), 1991) -
Criteria for Computer-Aided Form Evaluation
(The American Society of Mechanical Engineers (ASME), 1991) -
A Simplified Approach to Predict Elastic Pressure Distribution in Non-Hertzian Contact Stress Problems
(The American Society of Mechanical Engineers (ASME), 1991)An approximate but simple method to predict elastic pressure distribution in non-Hertzian contact stress problems has been developed using the two-dimensional Hertz relations and experimentally ... -
An Overview of Modeling and Simulation of the Milling Process
(The American Society of Mechanical Engineers (ASME), 1991) -
Mechanics of Bar Straightening, Part 1: General Analysis of Straightening Process
(The American Society of Mechanical Engineers (ASME), 1991)In the following paper, a general analysis of the mechanics involved in the straightening process of bars and sections by reverse kinematic loading has been made. -
Adaptive Compensation of Dynamic Characteristics for In-Process Sensors
(The American Society of Mechanical Engineers (ASME), 1991)Monitoring of machine tools and optimization of manufacturing processes require accurate values of in-process measured mechanical quantities such as force, torque, or displacement. Commercial sensors ... -
Effect of Machining Processes on the Fatigue Strength of Hardened AISI 4340 Steel
(The American Society of Mechanical Engineers (ASME), 1991)The effect of two finishing processes, namely, cutting and grinding, on the fatigue strength of hardened AISI 4340 steel was investigated. Three sets of flat tensile specimens were prepared by ... -
Automatic Disassembly and Total Ordering in Three Dimensions
(The American Society of Mechanical Engineers (ASME), 1991)Generating a sequence of motions for removing components in a three-dimensional assembly, one at a time, is considered—the robot motion being strictly translational. We map the boundary representation ... -
Mechanism of Cutting Force and Surface Generation in Dynamic Milling
(The American Society of Mechanical Engineers (ASME), 1991)An improved model of the milling process is presented. The model proposes a method of determining cutting forces in five distinct regions where the cutting edge travels during dynamic milling. ... -
Reduction of Springback and Residual Stresses During Winding of a Helical Spring
(The American Society of Mechanical Engineers (ASME), 1991)Wire exhibits considerable torsional springback after cold forming, by winding into a helical spring. This springback can be reduced by the application of a tensile pull during the winding ... -
Stresses and Deflections of Thick, Curved Plates
(The American Society of Mechanical Engineers (ASME), 1965)A solution is obtained using the linear theory of elasticity for the stresses in a long, thick, uniformly curved plate due to pressures on the curved surfaces and forces or deflections specified ... -
Analysis of Fluid Flow Under a Grinding Wheel
(The American Society of Mechanical Engineers (ASME), 1991)Fluid flow under a grinding wheel is modeled using a perturbation scheme. In this initial effort to understand the flow characteristics, we concentrate on the case of a smooth wheel with ... -
A Mechanistic Dynamic Model of End Milling for Process Controller Simulation
(The American Society of Mechanical Engineers (ASME), 1991)In an effort to maximize the metal removal rate in end milling while avoiding excessive cutter deflection or breakage, both fixed gain and adaptive controllers have been implemented for on-line ... -
Ductile-Regime Grinding: A New Technology for Machining Brittle Materials
(The American Society of Mechanical Engineers (ASME), 1991)Because of recent advances in precision engineering that allow controlled grinding infeed rates as small as several nanometers per grinding wheel revolution, it is possible to grind brittle ... -
Mechanics of Bar Straightening, Part 2: Straightening in Cross-Roll Straighteners
(The American Society of Mechanical Engineers (ASME), 1991)An analysis is made of the straightening process of rolled circular bars and tubes, with initial residual curvature in different types of cross-roll straighteners indicating the degree of ... -
Design of a High Energy Absorbing Urethane Cylinder for Ship Fendering Systems
(The American Society of Mechanical Engineers (ASME), 1991)A new design for a urethane cylinder is presented which exhibits very high energy absorption for a given maximum compressive force and for a given amount of urethane. These characteristics are ... -
Fundamentals of Machine Component Design
(The American Society of Mechanical Engineers (ASME), 1991)