Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5701-5720 of 7723
-
On the Problem of Spiralling in BTA Deep-Hole Machining
(The American Society of Mechanical Engineers (ASME), 1994) -
Modal Analysis of a Suspension Assembly
(The American Society of Mechanical Engineers (ASME), 1994)The dynamic characteristics of a suspension assembly are examined using new numerical and experimental techniques. The p-type finite element method is used to construct a numerical model of the ... -
In-Process Compensation for Milling Cutter Runout via Chip Load Manipulation
(The American Society of Mechanical Engineers (ASME), 1994) -
Finite Element Simulation of Chip Formation and Comparison with Machining Experiment
(The American Society of Mechanical Engineers (ASME), 1994)This paper presents a finite element model of orthogonal machining by using a 2-node link element to simulate chip separation. The chip and workpiece are connected by these link elements along ... -
Material Removal in WEDM of PCD Blanks
(The American Society of Mechanical Engineers (ASME), 1994)Polycrystalline diamond (PCD) tools are now widely used in machining a large variety of advanced materials. However, the manufacture of PCD tool blanks is not an economical and efficient process. ... -
The Origin and Interpretation of Spatial Frequencies in a Turned Surface Profile
(The American Society of Mechanical Engineers (ASME), 1994)An investigation into the origin of spatial frequencies within a turned surface profile is presented. A wavelength decomposition methodology is used to characterize the wavelength structure of ... -
An Analytic Mechanistic Cutting Force Model for Milling Operations: A Case Study of Helical Milling Operation
(The American Society of Mechanical Engineers (ASME), 1994) -
Lumped Multitorch Control of Welding During Production
(The American Society of Mechanical Engineers (ASME), 1994)In this article, multiple lumped thermomechanical characteristics of the welding process are regulated by modulation of the welding conditions in real time through feedback control. The controller ... -
The Profile Determination and Machining of Camoids with Oscillating Spherical Followers
(The American Society of Mechanical Engineers (ASME), 1994)A simple procedure, that can be used to determine the complicated camoid profile with an oscillating spherical follower and to decide the cutter path with the predictable surface roughness, is ... -
Stability of Turning Processes with Actively Controlled Linear Motor Feed Drives
(The American Society of Mechanical Engineers (ASME), 1994)Using linear motors as machine tool feed drives has the potential of enhancing machining performance by eliminating gear related mechanical problems and increasing speed and accuracy, but introduces ... -
An Analytic Mechanistic Cutting Force Model for Milling Operations: A Theory and Methodology
(The American Society of Mechanical Engineers (ASME), 1994) -
Modelling and Analysis of Pulse Electrochemical Machining (PECM)
(The American Society of Mechanical Engineers (ASME), 1994)A small interelectrode gap in Electrochemical Machining (ECM) results in improved dimensional accuracy control and simplified tool design. However, using a small gap with conventional ECM equipment ... -
Development of a Rational Basis for Design of Advanced Brushing Tools
(The American Society of Mechanical Engineers (ASME), 1994)In this paper, issues that are relevant to the design of brushing tool systems are examined and discussed. First, a general framework for brush design is presented that can provide a basis ... -
A Model of High Performance Dynamometer
(The American Society of Mechanical Engineers (ASME), 1994)A narrow frequency bandwidth, strong fluctuations of the gain versus signal frequency and sensitivity to disturbances caused by the operating environments are the most common factors limiting the ... -
Delamination-Free Drilling of Composite Laminates
(The American Society of Mechanical Engineers (ASME), 1994)Composite laminates in significant numbers are rendered unacceptable due to delamination that occurs during the drilling operation. Thrust generated during the drilling operation is identified as ... -
Tool Wear Monitoring at Turning
(The American Society of Mechanical Engineers (ASME), 1994)A new method for automatic tool wear monitoring at turning has been developed based on the analysis of the continuous acoustic emission (machining noise) generated by the tool during machining. ... -
Forecasting Control of Waterborne Basecoat Viscosity
(The American Society of Mechanical Engineers (ASME), 1994)Waterborne basecoat is gaining popularity in the automative industry. However, the viscosity of some waterborne basecoats may be unstable while circulating in the paint supply-and-storage system. ... -
Effect of Tool Geometry on Punching Performance
(The American Society of Mechanical Engineers (ASME), 1994)In today’s competitive industrial environment, the quality of a product is no longer the major factor which influences purchase by a customer, it is simply a prerequisite for competing in the ... -
A Knowledge-Based Diagnostic Approach for the Launch of the Auto-Body Assembly Process
(The American Society of Mechanical Engineers (ASME), 1994)This paper is the first attempt to implement a knowledge-based diagnostic approach for the auto-body assembly process launch. This approach enables quick detection and localization of assembly ... -
The Min-Max Load Criteria as a Measure of Machining Fixture Performance
(The American Society of Mechanical Engineers (ASME), 1994)Spherical-tipped locators and clamps are often used for the restraint of castings during machining. For structurally rigid castings, contact region deformation and micro-slippage are the predominant ...