Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5201-5220 of 7723
-
Transition Mechanisms Attendant to Large Amplitude Parametric Vibrations of Rectangular Plates
(The American Society of Mechanical Engineers (ASME), 1967)Experiments have been conducted to investigate the transition mechanisms attendant to the parametric vibrations of a simply supported rectangular plate subjected to a periodic load of the form ... -
Natural Frequencies in Annuli With Induced Thermal Membrane Stresses
(The American Society of Mechanical Engineers (ASME), 1967)A number of independent studies have concluded that initial, residual membrane stresses can increase the fundamental frequency or effective stiffness of thin circular disks and annuli. The present ... -
Torsional Vibration Analysis of a Hydrodynamic Split Torque Transmission
(The American Society of Mechanical Engineers (ASME), 1967)The steady-state torsional vibration for one mode of an engine transmission system was analyzed, and the analysis was verified by experimental data. The engine transmission system included a ... -
An Approximate Normal Mode Method for Damped Lumped Parameter Systems
(The American Society of Mechanical Engineers (ASME), 1967)An approximate normal mode method is introduced which permits any linear non-conservative system to be solved by super position of uncoupled coordinates. Accuracy of the method was found to be ... -
Mass-Spring-Damper Response to Repetitive Impact
(The American Society of Mechanical Engineers (ASME), 1967)The object of this research is the study of the response of a simple mass-spring-damper system to repetitive impact. The following analytical and experimental methods were employed: (a) Solution ... -
Deceleration of an Unbalanced Rotor Through a Critical Speed
(The American Society of Mechanical Engineers (ASME), 1967)The problem of a single-degree-of-freedom rotor decelerating slowly through its critica speed is solved by an energy approach; a closed solution is obtained. A small discontinuous downward jump ... -
Tribute to Den Hartog
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “Oil Whip Whirl Orbits of a Rotor in Sleeve Bearings” (Lund, J. W., and Saibel, E., 1967, ASME J. Eng. Ind., 89, pp. 813–823)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “The Influence of Trapped Fluids on High Speed Rotor Vibration” (Ehrich, F. F., 1967, ASME J. Eng. Ind., 89, pp. 806–812)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “A Quantitative Evaluation of Constrained-Layer Damping” (Yin, T. P., Kelly, T. J., and Barry, J. E., 1967, ASME J. Eng. Ind., 89, pp. 773–782)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “Vibration Analysis of Shells Using Discrete Mass Techniques” (McGrattan, R. J., and North, E. L., 1967, ASME J. Eng. Ind., 89, pp. 766–771)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “The Design and Evaluation of a Supercritical-Speed Helicopter Power-Transmission Shaft” (Prause, R. H., Meacham, H. C., and Voorhees, J. E., 1967, ASME J. Eng. Ind., 89, pp. 719–727)
(The American Society of Mechanical Engineers (ASME), 1967) -
Discussion: “Instability of Oil Bearings Due to High Oil Viscosity” (Chen, Y. N., 1967, ASME J. Eng. Ind., 89, pp. 697–704)
(The American Society of Mechanical Engineers (ASME), 1967) -
Analysis of End Milling Surface Error Considering Tool Compliance
(The American Society of Mechanical Engineers (ASME), 1998)An analytical model of surface height error in end milling due to the elastic compliance of cutting tool is presented. Based on the relationship of local cutting forces and chip thickness, ... -
Analysis of High Speed Axially Symmetric Cutting for Stripping Peripheral Coating
(The American Society of Mechanical Engineers (ASME), 1998)A theory of axially symmetric cutting is used to estimate the resistance to material removal of a composite cylinder undergoing stripping of a peripheral coating. The removal of materials from ... -
Using Wear Curves to Predict the Cost of Changes in Cutting Conditions
(The American Society of Mechanical Engineers (ASME), 1998)A recently-proposed probability model for cutting tool lifetimes based on tool wear curves is presented. Optimal tool replacement strategies and cutting conditions are calculated using this ... -
Suppression of Chatter Vibration in Drilling
(The American Society of Mechanical Engineers (ASME), 1998)In this study, from the viewpoint of suppressing chatter vibration in drilling, the effects of cutting conditions on the initiation boundary of chatter vibration were investigated experimentally. ... -
An Experimental Study of High Speed Orthogonal Cutting
(The American Society of Mechanical Engineers (ASME), 1998)A new high speed machining experiment is designed to obtain orthogonal cutting in a wide range of cutting speeds from 7 m/s to 100 m/s. Quasi-stationary cutting conditions are obtained. The ... -
Discussion: “Torsional Instability of Fully Stalled Airfoil (or Supercavitating Hydrofoil)” (Natesh, M. S., 1967, ASME J. Eng. Ind., 89, pp. 671–680)
(The American Society of Mechanical Engineers (ASME), 1967) -
Chip Formation Model of Cutting Fiber-Reinforced Plastics Perpendicular to Fiber Axis
(The American Society of Mechanical Engineers (ASME), 1998)The anisotropy of fiber-reinforced plastics heavily influences the chip formation and cut quality during machining. Fiber arrangement is found more dominant than the often stressed cutting conditions. ...