Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 3941-3960 of 7723
-
Application of Primary Sealing Criteria to a Self Energized Gasket
(The American Society of Mechanical Engineers (ASME), 1969)The seal on a metal-to-metal gasketed joint is effected by the imposition of bearing stresses, shearing stresses, or a combination of the two at the interface of the gasket and its mating ... -
Tools and Engineering Materials with Hard, Wear-Resistant Infusions
(The American Society of Mechanical Engineers (ASME), 1969)Development and evaluation of improved cutting tool materials which combine the high-strength properties of alloy tool steels with the higher hardness and increased wear resistance of metallic ... -
Comparison of Two Complete Solutions in an Axisymmetric Extrusion With Experiment
(The American Society of Mechanical Engineers (ASME), 1969)An upper-bound and a potential solution to a forward extrusion problem were compared with experimental results obtained by the visioplasticity method. The process consisted of extruding a 2-in-dia ... -
Analysis of an Offset Unsymmetric Gyroscope With Oblique Rotor Using (3×3) Matrices With Dual-Number Elements
(The American Society of Mechanical Engineers (ASME), 1969)Using 3 × 3 matrices of dual-number elements, dynamic equations are obtained for an offset unsymmetric gyroscope with obliquely placed rotor, a generalized six-degree-of-freedom gyroscopic ... -
What Sound Can Be Expected From a Worn Tool?
(The American Society of Mechanical Engineers (ASME), 1969)This paper describes an electronic-mechanical system which utilizes sonic signals to detect the degree of cutting edge wear in metalworking tools and automatically trigger a cutting edge change. ... -
Report of Survey Committee: Progress in Railway Mechanical Engineering, 1967–1968
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Displacement Analysis of Spatial Five-Link Mechanisms Using (3×3) Matrices With Dual-Number Elements” (Yang, A. T., 1969, ASME J. Eng. Ind., 91, pp. 152–157)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Problems on Hunting of Railway Vehicle on Test Stand” (Matsudaira, T., Matsui, N., Arai, S., and Yokose, K., 1969, ASME J. Eng. Ind., 91, pp. 879–885)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Incipient and Nucleate Boiling of Liquid Hydrogen” (Coeling, K. J., and Merte, Jr., H., 1969, ASME J. Eng. Ind., 91, pp. 513–520)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “General Aspects of the Lateral Dynamics of Railway Vehicles” (Wickens, A. H., 1969, ASME J. Eng. Ind., 91, pp. 869–875)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Development and Use of a Track Quality Index” (Crane, L. S., Sullivan, J. J., and Kaelin, C. R., 1969, ASME J. Eng. Ind., 91, pp. 861–867)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Dynamic Measurement of Absolute Track Properties” (Cass, R., Berthiaume, P. P., Kalita, R. E., and St-Louis, L., 1969, ASME J. Eng. Ind., 91, pp. 855–859)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Wheel-Rail Adhesion” (Marta, H. A., and Mels, K. D., 1969, ASME J. Eng. Ind., 91, pp. 839–846)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Shakedown as a Guide to the Design of Pressure Vessels” (Leckie, F. A., and Penny, R. K., 1969, ASME J. Eng. Ind., 91, pp. 799–806)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Analysis of Tool Wear—Part I: Theoretical Models of Flank Wear” (Bhattacharyya, A., and Ham, I., 1969, ASME J. Eng. Ind., 91, pp. 790–796)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Profile Measurement of Coated Abrasive Surfaces” (Story, R. W., and Keyes, E. J., 1969, ASME J. Eng. Ind., 91, pp. 781–786)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Investigation of Face-Milling Tool Temperatures by Simulation Techniques” (Wang, K. K., Tsao, K. C., and Wu, S. M., 1969, ASME J. Eng. Ind., 91, pp. 772–779)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Cup Drawing from an Anisotropic Blank” (Mir, W. A., and Hillier, M. J., 1969, ASME J. Eng. Ind., 91, pp. 766–771)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “Prediction of the One-Dimensional Equilibrium Cutting Gap in Electrochemical Machining” (Hopenfeld, J., and Cole, R. R., 1969, ASME J. Eng. Ind., 91, pp. 755–763)
(The American Society of Mechanical Engineers (ASME), 1969) -
Discussion: “A Study of Barreling as an Example of Free Deformation in Plastic Working” (Kulkarni, K. M., and Kalpakjian, S., 1969, ASME J. Eng. Ind., 91, pp. 743–754)
(The American Society of Mechanical Engineers (ASME), 1969)