Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 2301-2320 of 7723
-
Stylus Tracer Resolution and Surface Damage as Determined by Scanning Electron Microscopy
(The American Society of Mechanical Engineers (ASME), 1972)Stylus type instruments that employ needle tracers for examination of surfaces by means of translating the stylus over the surface and recording the undulations which occur during that traverse ... -
Upper-Bound Solutions to Tube Extrusion Problems Through Curved Dies
(The American Society of Mechanical Engineers (ASME), 1972)Velocity fields of tube extrusion problems through curved dies are presented for an incompressible material. These velocity fields are also applicable to conical and square-cornered dies. Thus, ... -
Shape and Flatness in Thin Strip Rolling
(The American Society of Mechanical Engineers (ASME), 1972)The paper describes measurements of lateral flow of material which took place during cold rolling thin strip. This sideways flow is shown to have a considerable influence of the final flatness ... -
A Solution of the Free Oblique Continuous Cutting Problem in Conditions of Light Friction at Chip-Tool Interface
(The American Society of Mechanical Engineers (ASME), 1972)A model for free oblique continuous cutting is proposed. In addition to the hypotheses used in Merchant’s model for free oblique continuous cutting, coincidence of chip-tool friction force with ... -
Water Reuse in the Food Processing Industry
(The American Society of Mechanical Engineers (ASME), 1972) -
Multicomponent Calibration of Machine-Tool Dynamometers
(The American Society of Mechanical Engineers (ASME), 1972)Service loads of machine-tool dynamometers are usually reduced to a system of three mutually orthogonal force components through a fixed reference point. Three additional components (moments) ... -
Modular Analysis of Geometry and Stresses in Closed-Die Forging: Application to a Structural Part
(The American Society of Mechanical Engineers (ASME), 1972)A computerized modular method is developed for predicting shape complexity, material volume, load, stress distributions, and center of loading in forgings. The method consists of dividing a forging ... -
On the Mechanics of Rectilinear Continuous Cutting With a Single Point Tool
(The American Society of Mechanical Engineers (ASME), 1972)Assuming plane shear surfaces and chip tool friction force in the direction of the relative displacement between chip and tool, the direction of chip flow is determined. The condition of minimum ... -
The Use of Superplastic Alloy of the Eutectic of Lead–Tin for the Analysis of Hot Extrusion Process
(The American Society of Mechanical Engineers (ASME), 1972)The dynamic similarity of two geometrically similar extrusion processes was examined. The flow lines, values of the flow function ψ, and velocity components were compared for the hot extrusion ... -
Plastic Indentation of Steel Cylinders With Circular Punches
(The American Society of Mechanical Engineers (ASME), 1972)The detailed deformation characteristics involved in axisymmetric plastic indentation was examined. Circular punches with flat and hemispherical ends were indented into specimens prepared from SAE ... -
Conical Acrylic Windows Under Long-Term Hydrostatic Pressure of 10,000 psi
(The American Society of Mechanical Engineers (ASME), 1972)Over 150 conical frustum acrylic plastic windows were subjected to 10,000 psi hydrostatic loading of up to 1000-hr duration in deep ocean simulators maintained at 65–75 deg F ambient temperature. ... -
Short-Time Acceptance Test for Machine Tools Based on the Random Nature of the Cutting Forces
(The American Society of Mechanical Engineers (ASME), 1972)A short-time dynamic acceptance test for machine tools based on a single measurement of a coefficient of dynamic stiffness (Kd ) is proposed. A feature of this test is that it takes into ... -
Enhancement of Tungsten-Carbide Tool Life by Oxide Treatment
(The American Society of Mechanical Engineers (ASME), 1972)It is shown that the tool life of tungsten-carbide tools can be increased by at least 80 percent by treating the surface of carbide tools with various oxides. Among the oxides that increase ... -
A Theoretical Analysis of Temperature Distributions in the High Speed Forging of Hot Steel
(The American Society of Mechanical Engineers (ASME), 1972)The power and forces required to fill a corner cavity in closed-die forging depend on the amount of transient thermal conduction from the heated billet into the cold die. The amount of this ... -
Optimization of Inertia Welding Process by Response Surface Methodology
(The American Society of Mechanical Engineers (ASME), 1972)The inertia welding process was investigated using Response Surface Methodology. The optimum welding condition to yield maximum breaking strength at the weld was attained through a steepest ascent ... -
Analysis of Chatter Vibration Through Step-Function Response
(The American Society of Mechanical Engineers (ASME), 1972)This paper deals with a challenge to apply the method of indicial response analysis for obtaining the frequency characteristics of total cutting system, tool system, and cutting zone. The ... -
Analysis of Lateral Extrusion of 6061-0 Aluminum by Slip Line Theory Modified to Include Strain-Hardening
(The American Society of Mechanical Engineers (ASME), 1972)An analytical solution for the symmetrical lateral extrusion process based on slip line theory is presented. The analysis incorporates the stress equations modified for strain-hardening and the ... -
Exhaust Vent Silencer Design
(The American Society of Mechanical Engineers (ASME), 1972)Noise control problems exist where high pressure, high temperature gasses are vented to the atmosphere. An example is used to illustrate an approach to the design of an acoustically treated ... -
Discussion: “Design of a Flash Stage for a Multistage Flash Evaporator” (Best, T. R., 1972, ASME J. Eng. Ind., 94, pp. 1179–1187)
(The American Society of Mechanical Engineers (ASME), 1972) -
Analysis of Drill Stress by Three-Dimensional Photoelasticity
(The American Society of Mechanical Engineers (ASME), 1972)An exploratory drill point stress analysis was obtained experimentally using a three-dimensional photoelastic technique. A drill model was stress-frozen under simulated drilling conditions and seven ...