Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1301-1320 of 7723
-
Effect of Particle Size Distribution on Powder Packing and Sintering in Binder Jetting Additive Manufacturing of Metals
(The American Society of Mechanical Engineers (ASME), 2017)The binder jetting additive manufacturing (AM) process provides an economical and scalable means of fabricating complex parts from a wide variety of materials. While it is often used to fabricate metal parts, it is typically ... -
Effects of Process Parameters on Friction Stir Spot Welding of Aluminum Alloy to Advanced High-Strength Steel
(The American Society of Mechanical Engineers (ASME), 2017)This paper studies a friction stir spot welding (FSSW) process that has been successfully applied to join aluminum alloy 6061-T6 to transformation-induced plasticity steel (TRIP) 780/800 steel. Cross sections of weld ... -
Analyses of Friction Stir Riveting Processes: A Review
(The American Society of Mechanical Engineers (ASME), 2017)This study presents detailed analyses of variant joining processes under the category of friction stir riveting (FSR) that are applied to assemble similar or dissimilar materials by integrating the advantages of both ... -
Size Distribution Estimation of Three-Dimensional Particle Clusters in Metal-Matrix Nanocomposites Considering Sampling Bias
(The American Society of Mechanical Engineers (ASME), 2017)Nanoparticle clustering phenomenon is a critical quality issue in metal-matrix nanocomposites (MMNCs) manufacturing. Accurate estimation of the 3D cluster size distribution based on the 2D cross section images is essential ... -
Pairwise Critical Point Detection Using Torque Signals in Threaded Pipe Connection Processes
(The American Society of Mechanical Engineers (ASME), 2017)The quality of threaded pipe connections is one of the key quality characteristics of drill pipes, risers, and pipelines. This quality characteristic is evaluated mainly by a pair of critical points, which are corresponding ... -
Three-Dimensional Finite Element Analysis of Skin-Pass Rolling and New Models for Process Control
(The American Society of Mechanical Engineers (ASME), 2017)This paper describes in detail the deformation behavior of the rolls and strip predicted from the three-dimensional finite element analysis of skin-pass rolling. The predictions are made on the basis of the coupled analysis ... -
Investigation on Weld Pool Dynamics in Laser Welding of AISI 304 Stainless Steel With an Interface Gap Via a Three-Dimensional Dynamic Model and Experiments
(The American Society of Mechanical Engineers (ASME), 2017)This paper reports on numerical and experimental investigations involving examination of the effects of an interfacial gap in the range of 0–0.3 mm on keyhole and molten pool dynamics. A numerical model was developed to ... -
Indirect Strain Control in Aluminum Stamp Formed Pans
(The American Society of Mechanical Engineers (ASME), 2017)A stamp forming die whose flexible blank holder (BH) was designed using finite element (FE) analysis was built. The tooling also included active draw beads, local wrinkling sensors, and local force transducers. Wrinkling ... -
Investigation of the Transient Characteristics for Laser Cladding Beads Using 420 Stainless Steel Powder
(The American Society of Mechanical Engineers (ASME), 2017)To understand the different aspects of the laser cladding (LC) process, process models can be of aid. Presently, the correct parameter settings for different manufacturing processes, such as machining and casting, are based ... -
A Molecular Dynamics Simulation Study of Material Removal Mechanisms in Vibration Assisted Nano Impact-Machining by Loose Abrasives
(The American Society of Mechanical Engineers (ASME), 2017)Vibration assisted nano impact-machining by loose abrasives (VANILA) is a novel nanomachining process to perform target-specific nano abrasive machining of hard and brittle materials. In this study, molecular dynamic (MD) ... -
Residual Stress Distribution in Silicon Wafers Machined by Rotational Grinding
(The American Society of Mechanical Engineers (ASME), 2017)Subsurface damage (SSD) and grinding damage-induced stress (GDIS) are a focus of attention in the study of grinding mechanisms. Our previous study proposed a load identification method and analyzed the GDIS in a silicon ... -
Microstructure Stability of a Fine-Grained AZ31 Magnesium Alloy Processed by Constrained Groove Pressing During Isothermal Annealing
(The American Society of Mechanical Engineers (ASME), 2017)In this study, an AZ31 magnesium alloy plate was processed by constrained groove pressing (CGP) under three deformation cycles at temperatures from 503 to 448 K. The process resulted in a homogeneous fine grain microstructure ... -
Metal Additive Manufacturing: Cost Competitive Beyond Low Volumes
(The American Society of Mechanical Engineers (ASME), 2017)Additive manufacturing (AM) is increasingly of interest for commercial and military applications due to its potential to create novel geometries with increased performance. For additive manufacturing to find commercial ... -
Laser Shock Peening for Suppression of Hydrogen-Induced Martensitic Transformation in Stress Corrosion Cracking
(The American Society of Mechanical Engineers (ASME), 2017)The combination of a susceptible material, tensile stress, and corrosive environment results in stress corrosion cracking (SCC). Laser shock peening (LSP) has previously been shown to prevent the occurrence of SCC on ... -
A Mathematical Model-Based Optimization Method for Direct Metal Deposition of Multimaterials
(The American Society of Mechanical Engineers (ASME), 2017)During the past few years, metal-based additive manufacturing technologies have evolved and may enable the direct fabrication of heterogeneous objects with full spatial material variations. A heterogeneous object has ... -
Modeling the Flow Behavior and Flow Rate of Medium Viscosity Alginate for Scaffold Fabrication With a Three-Dimensional Bioplotter
(The American Society of Mechanical Engineers (ASME), 2017)Tissue regeneration with scaffolds has proven promising for the repair of damaged tissues or organs. Dispensing-based printing techniques for scaffold fabrication have drawn considerable attention due to their ability to ... -
A Systematic Approach for Online Minimizing Volume Difference of Multiple Chambers in Machining Processes Based on High-Definition Metrology
(The American Society of Mechanical Engineers (ASME), 2017)The volume variation of multiple chambers of a workpiece is one of the most important factors that can directly influence the performance of the final product. This paper presents a novel systematic approach for online ... -
Melt Electrospinning Writing Process Guided by a “Printability Number”
(The American Society of Mechanical Engineers (ASME), 2017)The direct electrostatic printing of highly viscous thermoplastic polymers onto movable collectors, a process known as melt electrospinning writing (MEW), has significant potential as an additive biomanufacturing (ABM) ... -
Numerical Modeling of Metal-Based Additive Manufacturing Using Level Set Methods
(The American Society of Mechanical Engineers (ASME), 2017)The advance in computational science and engineering allows people to simulate the additive manufacturing (AM) process at high fidelity, which has turned out to be a valid way to model, predict, and even design the AM ... -
Cost Analysis and Fuzzy Control for Collapsible Container Usage Based on Closed-Loop Supply Chain Model
(The American Society of Mechanical Engineers (ASME), 2017)In the last decade, global competition has forced manufacturers to optimize logistics. The implementation of collapsible containers provides a new perspective for logistics cost savings, since using collapsible containers ...