Journal of Pressure Vessel Technology: Recent submissions
Now showing items 3121-3140 of 4506
-
Fluid Damping and Fluid Stiffness of a Tube Row in Crossflow
(The American Society of Mechanical Engineers (ASME), 1994)Motion-dependent fluid forces acting on a tube array were measured as a function of excitation frequency, excitation amplitude, and flow velocity. Fluid-damping and fluid-stiffness coefficients ... -
Optimization of a Compound Vessel Supported by the Wound Ribbon Cylinder
(The American Society of Mechanical Engineers (ASME), 1994)The paper deals with the optimal strength design of the belt chamber compound vessel of mixed construction, consisting of the matrix made of sintered carbide, supporting steel ring, and outer ... -
Response and Failure of Internal Structural Subsystems Under Blast and Shock Loading
(The American Society of Mechanical Engineers (ASME), 1994)The objective of this paper is to evaluate the ability to accurately predict the motions, structural response, and failure modes of internal structural components subjected to high-intensity ... -
A Kt-Based Method for Calculating LCF Life of Notched Specimens
(The American Society of Mechanical Engineers (ASME), 1994)Under cyclic loading, the effect of stress raisers on the fatigue life depends upon several parameters, the most important being the stress concentration factor, the stress level, and the ... -
Monitoring of Transient Temperature Distribution in Piping
(The American Society of Mechanical Engineers (ASME), 1994)A numerical method for monitoring temperature distribution in which boundary flux and initial state are unknown is presented. Regularizations based on Tikhonov and Beck’s method are employed. ... -
A Computational Procedure for Calculating Primary Stress for the ASME B&PV Code
(The American Society of Mechanical Engineers (ASME), 1994)A simple procedure for calculating primary stress consistent with the ASME B&PV Code is presented. The procedure is based on an iterative elastic analysis technique referred to as the elastic ... -
The Treatment of Residual Stress in Fracture Assessment of Pressure Vessels
(The American Society of Mechanical Engineers (ASME), 1994)The treatment of weld residual stress in the fracture assessment of cylindrical pressure vessels is considered through partitioning the stress into membrane, bending, and self-balancing through-wall ... -
Editorial
(The American Society of Mechanical Engineers (ASME), 1993) -
Extensive Modeling of High-Temperature Deformation Based on Unified Approach
(The American Society of Mechanical Engineers (ASME), 1993)A unified inelastic constitutive equation is proposed to describe the cyclic inelastic deformation of 2 1/4Cr-1Mo steel at 550°C. In the present study, an evolution of the overstress is ... -
Editorial
(The American Society of Mechanical Engineers (ASME), 1993) -
Editorial
(The American Society of Mechanical Engineers (ASME), 1993) -
Multiaxial Relaxation and Creep Damage Assessments—A Comparison of ASME N-47 and GLOSS Time-Scaling Methods
(The American Society of Mechanical Engineers (ASME), 1993)Two simplified methods for determining multiaxial relaxation and creep damage, the GLOSS time-scaling and the ASME Code Case N-47 method, are described in this paper. The theoretical basis and ... -
Design of Tubesheet for U-Tube Heat Exchangers
(The American Society of Mechanical Engineers (ASME), 1993)Thorough analysis of two-side integral tubesheet of U-tube heat exchanger is carried out, using Panc’s component theory of plates. Effects of solid annular rim and interaction between tubesheet ... -
Simple Bounds on Limit Loads by Elastic Finite Element Analysis
(The American Society of Mechanical Engineers (ASME), 1993)A method for bounding limit loads by an iterative elastic continuum finite element analysis procedure, referred to as the elastic compensation method, is proposed. A number of sample problems ... -
Impact Simulation of Liquid-Filled Containers Including Fluid-Structure Interaction—Part 2: Experimental Verification
(The American Society of Mechanical Engineers (ASME), 1993)In a number of applications, the hydrodynamic effect of a fluid must be included in the structural evaluation of liquid-filled vessels undergoing transient loading. Prime examples are liquid ... -
Primary Circuit Metal State With Regard to NPP Lifetime Extension
(The American Society of Mechanical Engineers (ASME), 1993) -
Hot Clamp Design for LMFBR Piping Systems
(The American Society of Mechanical Engineers (ASME), 1993)Thin-wall, large-diameter piping for liquid metal fast breeder reactor (LMFBR) plants can be subjected to significant thermal transients during reactor scrams. To reduce local thermal stresses, ... -
Study of the Fluid Flow in the Elliptical Duct by the Method of Characteristics
(The American Society of Mechanical Engineers (ASME), 1993)This study develops a mathematical model to determine the properties of laminar flow in the elliptical duct. With some assumptions, the nonlinear governing equations of the air in the elliptical ... -
Design and Analysis of a Test Coupon for Fusion Welding
(The American Society of Mechanical Engineers (ASME), 1993)The objective of a weld coupon is to provide a simple test to determine the effects of different welding parameters and constraints on the final state of fusion welds. With such a test it ... -
Pipeline Response to Directionally and Spatially Correlated Seismic Ground Motions
(The American Society of Mechanical Engineers (ASME), 1993)This study analyzes the response of continuous, straight, large diameter pipelines subjected to spatially and directionally correlated seismic ground motions. The stochastic characteristics of the ...