Journal of Engineering for Gas Turbines and Power: Recent submissions
Now showing items 3021-3040 of 9564
-
Discussion: “The Interaction of Air Motion, Fuel Spray, and Combustion in the Diesel Combustion Process” (Melton, Jr., R. B., and Rogowski, A. R., 1972, ASME J. Eng. Power, 94, pp. 11–14)
(The American Society of Mechanical Engineers (ASME), 1972) -
A Fiber Optics Probe for Measurements in Emitting-Absorbing Flames
(The American Society of Mechanical Engineers (ASME), 1972)In this paper, a fiber optics probe is described which is designed for diagnostics in emitting-absorbing flames. The probe is swept with constant speed through the flame to be investigated, ... -
Fireside Corrosion and Pollutant Emission from Crude Oil Combustion
(The American Society of Mechanical Engineers (ASME), 1972)A pilot-scale research boiler was used to evaluate the corrosion and pollution potential of a western Canadian mixed-blend crude oil from the Interprovincial Pipeline. It was demonstrated that ... -
Environmental Effects on the High-Temperature Corrosion of Superalloys in Present and Future Gas Turbines
(The American Society of Mechanical Engineers (ASME), 1972)Effects of temperature and contaminant levels on the high-temperature corrosion of superalloys used in gas turbines were investigated using pressurized passages which simulate the operating conditions ... -
Coal-Ash Composition as Related to High-Temperature Fireside Corrosion and Sulfur-Oxides Emission Control
(The American Society of Mechanical Engineers (ASME), 1972) -
Experience With Throat-Tap Nozzles for Accurate Flow Measurement
(The American Society of Mechanical Engineers (ASME), 1972)During the past 10 years considerable experience has been gained in the use of ASME throat-tap nozzles for accurate flow measurement. Numerous precision calibrations have established turbulent ... -
Combustion and Fouling Characteristics of Two Canadian Lignites
(The American Society of Mechanical Engineers (ASME), 1972)The report describes combustion tests with Bienfait lignite from Saskatchewan and Onakawana lignite from James Bay. They were burned in a pilot-scale, pulverized-fired boiler primarily to study ... -
New Particle Size Measuring Probe—Application to Aerosol Collector and Emissions Evaluations
(The American Society of Mechanical Engineers (ASME), 1972)A basic parameter needed for judicious design, selection, and regulation of industrial gas cleanup equipment is particle size distribution of gas-borne emissions. Despite the importance of this ... -
Nonradioactive Tracer for Performance Tests of Steam Turbines in PWR Systems
(The American Society of Mechanical Engineers (ASME), 1972)This paper reports on the experience gained by the authors in the use of a nonradioactive sodium tracer in limited-scope testing in power plants with nuclear steam supply systems. It shows ... -
An Investigation of Nonequilibrium Effects in an Internal Combustion Engine
(The American Society of Mechanical Engineers (ASME), 1972)A theoretical analysis of the basic chemical kinetic processes which lead to the formation and partial decomposition of nitric oxide and carbon monoxide has been undertaken. A mathematical model ... -
Average Pressure Measurement in Low-Velocity Nonuniform Gas Flows
(The American Society of Mechanical Engineers (ASME), 1972)An accurate measurement of the average stagnation pressure at a duct cross section is necessary when trying to determine the loss characteristics of low-pressure loss components such as power ... -
Analysis of Feedwater Pump Suction Pressure Decay Under Instant Turbine Load Rejection
(The American Society of Mechanical Engineers (ASME), 1972)As steam-electric generating plant unit sizes increase, and as the capacities of the feedwater pumps increase, the design provision of an adequate suction for the safe operation of the feedwater ... -
The Generation of Pollution-Free Electrical Power From Solar Energy
(The American Society of Mechanical Engineers (ASME), 1972)Projections of the U. S. electrical power demands over the next 30 years indicate that the U. S. could be in grave danger from power shortages, undesirable effluence, and thermal pollution. ... -
A Proposed New Concept for a Solar-Energy Converter
(The American Society of Mechanical Engineers (ASME), 1972)The potential advantages of terrestrially utilizing nonpolluting solar energy are well-known. One of the more promising approaches to achieving the desired high solar-electrical conversion efficiency ... -
Erratum: “Discussion of ‘Thermal Cycle Arrangements for Power Plants Employing Dry Cooling Towers’” (Journal of Engineering for Power, 1972, 94, pp. 70–71)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “A Fiber Optics Probe for Measurements in Emitting-Absorbing Flames” (Sakkal, F., Heberlein, J., and Pfender, E., 1972, ASME J. Eng. Power, 94, pp. 159–165)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “New Particle Size Measuring Probe—Application to Aerosol Collector and Emissions Evaluations” (Downs, W., and Strom, S. S., 1972, ASME J. Eng. Power, 94, pp. 117–123)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “Nonradioactive Tracer for Performance Tests of Steam Turbines in PWR Systems” (Deming, N. R., and Feldman, R. W., 1972, ASME J. Eng. Power, 94, pp. 109–114)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “An Investigation of Nonequilibrium Effects in an Internal Combustion Engine” (Spadaccini, L. J., and Chinitz, W., 1972, ASME J. Eng. Power, 94, pp. 98–107)
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “Analysis of Feedwater Pump Suction Pressure Decay Under Instant Turbine Load Rejection” (Liao, G. S., and Leung, P., 1972, ASME J. Eng. Power, 94, pp. 83–88)
(The American Society of Mechanical Engineers (ASME), 1972)